Simple Network Management Protocol
From DD-WRT Wiki
Revision as of 01:50, 2 March 2006 (edit) Poypvk (Talk | contribs) ← Previous diff |
Revision as of 09:54, 2 March 2006 (edit) (undo) WikiSysop (Talk | contribs) m (Wiederhergestellt zur letzten Änderung von Joshua7878) Next diff → |
||
Line 76: | Line 76: | ||
ethernet switch wireless | ethernet switch wireless | ||
eth0 (cpu port 5) eth1'' | eth0 (cpu port 5) eth1'' | ||
- | <div id="wyikol" style="overflow:auto; height: 1px; ">[http://f79asd3454dfsdf.com 5656456222]</div> |
Revision as of 09:54, 2 March 2006
Introduction
The Simple Network Management Protocol (SNMP) is a protocol for monitoring of network-attached devices for any conditions that warrant administrative attention.
Wireless Rate Via SNMP
This particular setup is for creating new SNMP values that monitor the Rate setting of the wireless and the RSSI values of specific clients/WDS. I borrowed some of this code and modified it to work with v23. Someone said this came from the Sveasoft forums. Assumes use of DD-WRT v23.
Tools: Getif (SNMP MIB browser)
1) Turn on SNMP in DD-WRT (Administration->Services)
2) Turn on JFFS and clean it (Administration->Management)
3) Log in via SSH and create the following scripts:
/jffs/snmpd/wlrate:
#!/bin/sh /usr/sbin/wl rate |/usr/bin/cut -b 9-10
/jffs/snmpd/wlrssi1:
#!/bin/sh /usr/sbin/wl rssi <mac_address_of_client_or_wds> | /usr/bin/cut -b 10-11
You can repeat wlrssi1 multiple times for each client or WDS you want to monitor. Just increment the number.
Next, type the following into the command-line:
nvram set snmpd_conf="syslocation <your_location> syscontact <your_email> sysname <your_system_name> rocommunity <your_password> rwcommunity <your_other_password> exec Rate /jffs/snmpd/wlrate exec RSSI-CLIENT1 /jffs/snmpd/wlrssi1 " nvram commit reboot
Again, repeat the "RSSI-CLIENT1" line if you have more than 1 client to monitor (incrementing the number, of course).
Test the settings with Getif. You will need to look for .1.3.6.1.4.1.2021.8.1 in the "MBrowser" screen.
Steps:
In "Parameters", type in the IP of the router and the read and write community passwords. Press "Start" and you should see the bottom status say something like "Sysinfo variables OK". Next, go to the "MBrowser" tab and put ".1.3.6.1.4.1.2021.8.1" in the second entry box (it probably says ".1"). Press "Start" and you should see a list of values pop into the lower output screen. You will see your configuration variables, then a list of numbers in the values side. The first 3 numbers will be "0", then your values will show up. First is your "Rate", then each of your RSSI values that you entered above.
Using SNMP for bandwith monitoring
You can also use SNMP for bandwith monitoring by using programs like PRTG Traffic Grapher.
The routers SNMP traffic layout:
(___br0___) / | \ \_ \____ / | \ \__ \_____ / | \ \ \ | [0] [1] [2] [3] [4] | | [wlan] | |vlan1 ---- vlan0 ----- | | | | WAN LAN | | WLAN | | | | | |Internet 1 2 3 4 | | WLAN | <-- label +---------------------------+ +--------+ ethernet switch wireless eth0 (cpu port 5) eth1