Asus RT-N15

From DD-WRT Wiki

(Difference between revisions)
Jump to: navigation, search
Revision as of 15:03, 2 April 2018 (edit)
Ian5142 (Talk | contribs)
(Added link to Where do I download firmware.)
← Previous diff
Revision as of 15:03, 25 May 2018 (edit) (undo)
Ian5142 (Talk | contribs)
(Removed specs, linked to wikidevi page.)
Next diff →
Line 4: Line 4:
==Specs== ==Specs==
- This section is in need of cleanup!+See wikidevi page for full specs: https://wikidevi.com/wiki/ASUS_RT-N15
-Platform+
- Serial Num. = ?+
- FCC ID = [https://fjallfoss.fcc.gov/oetcf/eas/reports/ViewExhibitReport.cfm?mode=Exhibits&RequestTimeout=500&calledFromFrame=N&application_id=240914&fcc_id=%27MSQ-RTN15%27 MSQ-RTN15]+
- CPU Type = Ralink RT2880F GV76440C0 0740ST+
- MIPS Rev = ?+
- CPU Speed = 266MHz+
- Bus = ?+
- Flash Type = Parallel+
- Flash Chip = MX T072421 29LV320CBT 2U761500A1+
- Flash Size = 4MB+
- RAM Size = 32MB (2x 16MB)+
- RAM Chip = Samsung 743 K4S281632K-UCG0+
- nvram Size = ?+
- Switch = Ralink RTL8366SR 7A085S2 G742B+
- Port-based vlan = ?+
- 802.1q vlan = ?+
- Ethernet Port Count = 1-10/100/1000-WAN 4-10/100/1000-LAN+
- Wired Standard = ?+
- boot_wait = ?+
- CF Card Socket = No+
- SD/MMC Mod Support = No+
- MiniPCI slots = No+
- PoE = No+
- Power = 5V/2.5A+
- Color of LEDs = ?+
- USB = No+
- Serial Port = 1+
- JTAG Port = No+
- Supported by TJTAG 3.02 = ?+
- Supported by dd-wrt as of = WIP as of [http://svn.dd-wrt.com:8000/dd-wrt/changeset/16019 16019]+
- dd-wrt K2.4 Support = No+
- dd-wrt K2.6 Support = Yes+
- Special Features = Gigabit Switch+
-Radio+
- Wireless Radio = Ralink RT2820L CV13930B 07125T+
- WLAN DSP processor = ?+
- Antenna Connector Type = Internal+
- Wireless Standard = b/g/n+
- WiFi Operating Frequency = 2.4GHz ~ 2.5GHz+
- 802.11n Draft = up to 300Mbps+
- 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps+
- 802.11b = 1, 2, 5.5, 11Mbps+
- Radio cor_rev = ?+
- Radio Capabilities = ?+
==Threads of interest== ==Threads of interest==

Revision as of 15:03, 25 May 2018

Contents

NOTE: This device is a WIP.
NOTE: Requires K2.6, Do not flash anything else.
NOTE: During configuration or flashing a device, the only things that should be hooked to the device is the computer and power.

Specs

See wikidevi page for full specs: https://wikidevi.com/wiki/ASUS_RT-N15

Threads of interest

Flashing

The device is stitched from windows Firmware update in an official insertion (the version of an insertion 1.0.0.7)

Firmware files can be found here: Where do I download firmware? (asus-rt-n15 folder).

Upgrading

This section is in need of cleanup!

Reverting

For reset it is necessary to translate the device to an original insertion in a recovery mode. 1. We install program Restoration Firmware. 2. We drop device adjustments. 3. We disconnect the device. 4. We push the button ресет and we include a supply, without releasing the button ресет, we wait when the power indicator will start blinking, we release the button ресет. 5. We launch program Restoration Firmware, we select a file with an insertion, we stitch. 6. After a reinsertion we come into a router and we drop adjustments on the factory. We ungear the device. 7. We include a router and it is provisionable.

JTAG/Serial Info

JTAG

This router does not have JTAG.

Serial

Serial Pinouts
This section is in need of cleanup!
Hyper terminal Setup in Windows XP
In Windows XP, Click Start Button - All Programs - Accessories - 
   Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
Set:
 Bits per second = 115200
 Data Bits = 8
 Parity = none
 Stop bits = 1
 Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you 
             don't have to enter the settings again.
Putty Setup in Windows XP
After installing putty, run it
 Serial line = The COM port your using for serial (ie. COM3)
 Speed = 115200
Click on Serial under Connection
 Serial line to connect to = same as above (Serial line)
 Speed (baud) = 115200
 Data bits = 8
 Stop bits = 1
 Parity = None
 Flow control = None
Click Session
 Enter a name for your connection under saved sessions
Click Save
Click Open
Serial Recovery
This section is in need of Serial Recovery Instructions!

Notes