Xbee

From DD-WRT Wiki

(Difference between revisions)
Jump to: navigation, search
Revision as of 14:47, 10 May 2010 (edit)
Jeremyj (Talk | contribs)

← Previous diff
Revision as of 14:51, 10 May 2010 (edit) (undo)
Jeremyj (Talk | contribs)

Next diff →
Line 21: Line 21:
The AdaFruit site has a link to configuring the radios which is excellent (http://www.humboldt.edu/~cm19/XBee%20setup.pdf). Read through the document and setup one radio as the coordinator and the other as the end device. You can also visit the Funnel site and grab their software to configure the radios(http://code.google.com/p/funnel/downloads/list). Download the XbeeConfigTool.zip. This software seems easier to use but has less option for configuring the radios. The AdaFruit site has a link to configuring the radios which is excellent (http://www.humboldt.edu/~cm19/XBee%20setup.pdf). Read through the document and setup one radio as the coordinator and the other as the end device. You can also visit the Funnel site and grab their software to configure the radios(http://code.google.com/p/funnel/downloads/list). Download the XbeeConfigTool.zip. This software seems easier to use but has less option for configuring the radios.
-Remember that to set the baud rate to 115200, that is the baud rate of the router, and I am not sure if it can be changed.+Remember that to set the baud rate to 115200, that is the baud rate of the router, and I am not sure if it can be changed. If somebody can tell me how to change the baud rate of the router, then by all means let me know!
 + 
 +'''XBee hookup to Router'''
 +Attach the 3.3Volt of the XBee carrier board to
 + 
 +Attach the GND pin of the XBee carrier board to
 + 
 +Attach the TX pin of the XBee carrier board to
 + 
 +Attach the RX pin of the XBee carrier board to

Revision as of 14:51, 10 May 2010

Xbee Serial Port Radio Link

Using AdaFruit Xbee carrier boards, you can add a Xbee radio link to the router. The radios I am using are rated for a maximum distance of 300 feet and cost around $20, however, you can upgrade the radios and there are some that go 1 mile, but cost twice as much. SparkFun electronics has a greater inventory of radios.

What you will need:

2 Xbee radios(http://www.adafruit.com/index.php?main_page=product_info&cPath=29&products_id=128)

2 Xbee carrier boards(http://www.adafruit.com/index.php?main_page=product_info&cPath=29&products_id=126)

1 USB FTDI cable(http://www.adafruit.com/index.php?main_page=product_info&cPath=29&products_id=70)

Female jumper wires(http://www.sparkfun.com/commerce/product_info.php?products_id=9389)

XCTU software to configure the radios(http://www.digi.com/support/productdetl.jsp?pid=3352&osvid=57&tp=5&s=316)

Make the Xbee Carrier Boards Again, visit the AdaFruit site and user her instructions for making the boards(http://www.ladyada.net/make/xbee/index.html).

Configuring the Radios The AdaFruit site has a link to configuring the radios which is excellent (http://www.humboldt.edu/~cm19/XBee%20setup.pdf). Read through the document and setup one radio as the coordinator and the other as the end device. You can also visit the Funnel site and grab their software to configure the radios(http://code.google.com/p/funnel/downloads/list). Download the XbeeConfigTool.zip. This software seems easier to use but has less option for configuring the radios.

Remember that to set the baud rate to 115200, that is the baud rate of the router, and I am not sure if it can be changed. If somebody can tell me how to change the baud rate of the router, then by all means let me know!

XBee hookup to Router Attach the 3.3Volt of the XBee carrier board to

Attach the GND pin of the XBee carrier board to

Attach the TX pin of the XBee carrier board to

Attach the RX pin of the XBee carrier board to