Wiviz
From DD-WRT Wiki
Wiviz, an open source GPL project, allows you to use your WRT to see other networks. Using a dynamic Javascript-based interface it scans for networks and then shows signal strength and effects of antenna adjustment in real time! Thanks to User Lament who has ported Wiviz to DD-WRT!
Contents |
Installation
First enable jffs2, and clean jffs2, found under the administration tab/management tab of the web DD-WRT Control Interface, if you have not done so already.
Use telnet or SSH (if enabled) to log in as root on the router. If using Windows XP, you can type 'telnet' from a run command, and use the command 'open 192.168.1.1' (assuming your router ip is 192.168.1.1), to gain access to the router. Type 'root' as username, and your router password, as the password.
Next type the following commands (in bold).
cd /jffs/ This puts us in the jffs directory from root directory
wget http://lament.rutka.net/wiviz-jffs.tar.gz This downloads the permanent (ie, stored in jffs file structure) program
tar -xvzf wiviz-jffs.tar.gz This extracts files
ln -s /jffs/www /tmp/ This makes the symlink. Please note that there are 3 spaces in this line
If the symbolic link already exists the command ln -s /jffs/www /tmp/ will fail and you will first have to use : rm -r /tmp/www and then ln -s /jffs/www /tmp/
That should allow your browser to see the wiviz page at
http://192.168.1.1/user/wiviz/wiviz.html or http://routerip/user/wiviz/wiviz.html
Finally clean up by typing
rm wiviz-jffs.tar.gz This will remove the downloaded compressed file
USING A SAMBA SHARE INSTEAD OF JFFS If you lack the space necessary to install on JFFS (Using a large installation on a WRT54G is the usual reason) you can simulate JFFS using a network share. See jffs on WRT54G. Then just follow the above instructions.
IMPORTANT: The link is only for the current session, and must be recreated for each session. Perform the following instructions to create the link automatically on startup.
You will need to create a subdirectory /jffs/etc/ if it doesn't already exist.
ls /jffs/ List the jffs/ directory to see if etc/ exists.
If not, then mkdir /jffs/etc Makes the new subdirectory etc/
mkdir /jffs/etc/config Creates a new subdirectory to /jffs/etc/ of config/
echo "rm -r /tmp/www" > /jffs/etc/config/wi-viz.startup Creates startup file with first line
echo "ln -s /jffs/www /tmp/" >> /jffs/etc/config/wi-viz.startup Appends second line
chmod 700 /jffs/etc/config/wi-viz.startup Sets file permissions
Note: The wiviz page only displays output - the input settings do not function with DD-WRT.
In order to get around not being able to change to channel hopping, you can manually create a wiviz config file.
echo "channelsel=hop&hopseq=1,6,11" > /tmp/wiviz-cfg
channelsel = Either the word "hop" or the channel number to monitor. The default is to monitor the channel already in use by the card.
hopseq = A comma seperated list of channels to hop through in the order of your choice.
Remember: Channel hopping does NOT work when in AP mode.
Wishlist
- Integrate Wiviz by means of links into the routers HTTP system
- Graphical signal strength and noise plot function
- List stations mode with their signal strength graph on the side (to allow to identifiy directions when scanning using directional antennae)
- Automate antenna comparison by using the firmware antenna selector function
- Can IPs be extracted from the packets?
Buglists
- sometimes network icons drift out of the screen and everything shifts out of sight:
-> Solution: Replace the declump function in wiviz.js Java Script with this:
function declump() { var c = 0; var top = 150,bottom = -350,left = 550,right = -550; for (i = 0; i < hosts.length; i++) { for (j = 0; j < hosts.length; j++) { if (i == j) continue; e1 = document.getElementById(hosts[i].mnem); e2 = document.getElementById(hosts[j].mnem); if (!e1 || !e2) continue; x1 = parseInt(e1.style.left); x2 = parseInt(e2.style.left); y1 = parseInt(e1.style.top); y2 = parseInt(e2.style.top); ox = x2; oy = y2; if (x2 > left) x2 = left; if (x2 < right) x2 = right; if (y2 > top) y2 = top; if (y2 < bottom) y2 = bottom; dist = Math.sqrt(Math.pow((x1-x2), 2) + Math.pow((y1-y2), 2)); if (dist == 0) { x2 += Math.random() * 5; y2 += Math.random() * 5; dist = 10; } if (dist < 100) { cx = (x1-x2) * 5 / (dist / 3); cy = (y1-y2) * 5 / (dist / 3); x2 -= cx; y2 -= cy; } if (hosts[j].apmnem == hosts[i].mnem || hosts[i].apmnem == hosts[j].mnem) { if (dist > 150) { cx = (x1-x2) * 5 / (dist / 3); cy = (y1-y2) * 5 / (dist / 3); x2 += cx; y2 += cy; } } if (Math.abs(ox-x2) > 2 || Math.abs(oy-y2) > 2) { e2.style.left = parseInt(x2); e2.style.top = parseInt(y2); c++; } } }