Watchguard Firebox Edge

From DD-WRT Wiki

(Difference between revisions)
Jump to: navigation, search
Revision as of 14:52, 28 July 2011 (edit)
Sash (Talk | contribs)

← Previous diff
Current revision (17:15, 28 July 2011) (edit) (undo)
Sash (Talk | contribs)

 
(11 intermediate revisions not shown.)
Line 6: Line 6:
=Install DD-WRT= =Install DD-WRT=
- redboot pw?+==Via Serial Port==
 + 
 +==Reset==
 +The device can be reset to factory defaults by holding down the reset button when powering up
=Hardware= =Hardware=
-*Intel IXP 422 @ 2663MHz+*Intel IXP 422 @ 266MHz
*6x 10/100Mbps ports (Marvell 88E6060) *6x 10/100Mbps ports (Marvell 88E6060)
*1x mPCI (optional WIFI) *1x mPCI (optional WIFI)
-*64MB (128MB?) SD-RAM+*128MB SD-RAM
*1MB NOR Flash *1MB NOR Flash
*64MB NAND Flash *64MB NAND Flash
*12V/1.2A PSU *12V/1.2A PSU
-*1x RS232+*2x RS232
 +*Backup battery (+)
 + 
 + 
 +(+) The switch on the PCB enables/disables the backup battery. Default is enabled. With it enabled going throught the factory reset procedure will restore the firmware but not your settings (local IP, admin logon etc...). Resetting with the switch off trully resets everything.
==Serial port== ==Serial port==
 +
 +You have to hold the reset button while powering on to see the boot up on the rear serial connector. Serial settings 115200 bps,8,N,1 <br>
 +Password: '''F5BA25AB44724fb5A6DD37554809CE34'''
 +
 +===Internal===
 +
 +serial pinout: <br>
 +1: 3.3V <br>
 +2: Rx <br>
 +3: Tx <br>
 +4: GND <br>
 +
 +=Links=
 +http://www.dd-wrt.com/phpBB2/viewtopic.php?t=72341
[[Category:Hardware]] [[Category:Hardware]]

Current revision

This tutorial gives you infromation about the Watchguard Firebox Edge series which includes the models X10e(-W), X20e(-W) and X55e(-W)

Contents


[edit] Install DD-WRT

[edit] Via Serial Port

[edit] Reset

The device can be reset to factory defaults by holding down the reset button when powering up

[edit] Hardware

  • Intel IXP 422 @ 266MHz
  • 6x 10/100Mbps ports (Marvell 88E6060)
  • 1x mPCI (optional WIFI)
  • 128MB SD-RAM
  • 1MB NOR Flash
  • 64MB NAND Flash
  • 12V/1.2A PSU
  • 2x RS232
  • Backup battery (+)


(+) The switch on the PCB enables/disables the backup battery. Default is enabled. With it enabled going throught the factory reset procedure will restore the firmware but not your settings (local IP, admin logon etc...). Resetting with the switch off trully resets everything.

[edit] Serial port

You have to hold the reset button while powering on to see the boot up on the rear serial connector. Serial settings 115200 bps,8,N,1
Password: F5BA25AB44724fb5A6DD37554809CE34

[edit] Internal

serial pinout:
1: 3.3V
2: Rx
3: Tx
4: GND

[edit] Links

http://www.dd-wrt.com/phpBB2/viewtopic.php?t=72341