WDS-AP to WDS-Sta (Atheros) Example
From DD-WRT Wiki
Revision as of 15:26, 15 January 2008 (edit) Samueldg (Talk | contribs) (→Configuring the devices) ← Previous diff |
Revision as of 15:33, 15 January 2008 (edit) (undo) Samueldg (Talk | contribs) (→Setup->Basic Setup page) Next diff → |
||
Line 40: | Line 40: | ||
Section Optional Settings: | Section Optional Settings: | ||
* Router and Hostnames: '''acbr51''', '''acbr52''', '''acbr53''' (each name with each device). | * Router and Hostnames: '''acbr51''', '''acbr52''', '''acbr53''' (each name with each device). | ||
- | * Domain Name: '''mydomain''' | + | * Domain Name: '''mydomain''' (put yours here if you want). |
+ | Section Router IP: | ||
+ | * Local IP Address: '''192.168.2.51''', '''192.168.2.52''', '''192.168.2.53''' (each IP with each device) | ||
+ | * Subnet Mask: '''255.255.255.0''' | ||
+ | * Gateway: '''192.168.2.254''' (leave in blank if you don't use) | ||
+ | * Local DNS: '''192.168.2.254''' (leave in blank if you don't use) | ||
+ | Section DHCP: | ||
+ | * DHCP Server: '''Disable''' (Enable and configure if you want, I don't use it here). | ||
+ | Section Time Settings: | ||
+ | * Time Server: '''192.168.2.254''' (leave in blank if you don't use) | ||
===WiFi Parameters=== | ===WiFi Parameters=== | ||
===WDS Parameters=== | ===WDS Parameters=== |
Revision as of 15:33, 15 January 2008
Contents |
Simple LAN WDS configuration
Objective
Connect 3 LAN using 2 GW2347 and 1 GW2348 and they will be transparent for the diferent Ethernet subnets.
GW2347_0 - - - - - GW2348 - - - - - - GW2347_1 | | | LAN LAN LAN
Will support Spaning tree protocol to alow the case when GW2347's were in the same Ethernet segment. This case:
GW2347_0 - - - - - GW2348 | | GW2347_1 - - - - - - -
Definitions
The 3 LAN's are in the same IP subnet 10.1.1.0/24 (for example).
The GW234x management IP will be in 192.168.5.0/24 (for example).
All the GW234x has Winstron CM9 miniPCI cards into them.
Names of GW234x devices will be:
acbr51 with 192.168.2.51 for the GW2347_0
acbr52 with 192.168.2.52 for the GW2348
acbr53 with 192.168.2.53 for the GW2347_1
Prerequisites
All GW234x devices are with factory defaults configuration (all has their nvram erased using RedBoot commands).
Configuring the devices
I only coment the parameters I changed or if the parameter value is important for our purpose.
IP Parameters
Setup->Basic Setup page
Section WAN:
- Connection Type: Disabled
- STP: Enabled
Section Optional Settings:
- Router and Hostnames: acbr51, acbr52, acbr53 (each name with each device).
- Domain Name: mydomain (put yours here if you want).
Section Router IP:
- Local IP Address: 192.168.2.51, 192.168.2.52, 192.168.2.53 (each IP with each device)
- Subnet Mask: 255.255.255.0
- Gateway: 192.168.2.254 (leave in blank if you don't use)
- Local DNS: 192.168.2.254 (leave in blank if you don't use)
Section DHCP:
- DHCP Server: Disable (Enable and configure if you want, I don't use it here).
Section Time Settings:
- Time Server: 192.168.2.254 (leave in blank if you don't use)