WDS-AP to WDS-Sta (Atheros) Example

From DD-WRT Wiki

(Difference between revisions)
Jump to: navigation, search
Revision as of 15:54, 15 January 2008 (edit)
Samueldg (Talk | contribs)
(Wireless -> Basic Settings page)
← Previous diff
Current revision (15:08, 2 April 2018) (edit) (undo)
Ian5142 (Talk | contribs)
(Changed to internal link.)
 
(17 intermediate revisions not shown.)
Line 1: Line 1:
-=Simple LAN WDS configuration=+This page is now deprecated, instead see: [[WDS_Linked_router_network|WDS Linked router network]]
-==Objective==+
-Connect 3 LAN using 2 GW2347 and 1 GW2348 and they will be transparent for the diferent Ethernet subnets.+
- +
- GW2347_0 - - - - - GW2348 - - - - - - GW2347_1+
- | | |+
- LAN LAN LAN+
- +
-Will support Spaning tree protocol to alow the case when GW2347's were in the same Ethernet segment. This case:+
- GW2347_0 - - - - - GW2348+
- | |+
- GW2347_1 - - - - - - -+
- +
-==Definitions==+
-The 3 LAN's are in the same IP subnet 10.1.1.0/24 (for example).+
- +
-The GW234x management IP will be in 192.168.5.0/24 (for example).+
- +
-All the GW234x has Winstron CM9 miniPCI cards into them.+
- +
- +
-Names of GW234x devices will be:+
- +
-acbr51 with 192.168.2.51 for the GW2347_0+
- +
-acbr52 with 192.168.2.52 for the GW2348+
- +
-acbr53 with 192.168.2.53 for the GW2347_1+
- +
-==Prerequisites==+
-All GW234x devices are with factory defaults configuration (all has their nvram erased using RedBoot commands).+
- +
-All GW234x devices has ddwrt v24 RC 6.2 (or newer) flashed.+
- +
-==Configuring the devices==+
-I only coment the parameters I changed or if the parameter value is important for our purpose.+
- +
-===IP Parameters===+
-====Setup->Basic Setup page====+
-Section WAN:+
-* Connection Type: '''Disabled'''+
-* STP: '''Enabled'''+
-Section Optional Settings:+
-* Router and Hostnames: '''acbr51''', '''acbr52''', '''acbr53''' (each name with each device).+
-* Domain Name: '''mydomain''' (put yours here if you want).+
-Section Router IP:+
-* Local IP Address: '''192.168.2.51''', '''192.168.2.52''', '''192.168.2.53''' (each IP with each device)+
-* Subnet Mask: '''255.255.255.0'''+
-* Gateway: '''192.168.2.254''' (leave in blank if you don't use)+
-* Local DNS: '''192.168.2.254''' (leave in blank if you don't use)+
-Section DHCP:+
-* DHCP Server: '''Disable''' (Enable and configure if you want, I don't use it here).+
-Section Time Settings:+
-* Time Server: '''192.168.2.254''' (leave in blank if you don't use)+
- +
-===WiFi Parameters===+
-====Wireless -> Basic Settings page====+
-In each interface I thanged this parameters:+
-* Regulatory Domain: '''SPAIN''' (I'm in Spain).+
-* Wireless Mode: '''AP''' (Will be a simple WDS).+
-* Wireless Network Mode: '''A-Only''' (There are many home networks in 2,4GHz).+
-* Turbo Mode: '''Enabled''' (Is not required, but I want to test it).+
-* Outdoor Band: '''Enabled''' or '''Disabled'''. This allow you to select the indoor channels or the outdoor ones.+
-* Wireless Network Name (SSID): '''myssid''' (I use the same in all interfaces).+
-* Wireless Channel: '''106-Outdoor-Turbo''' for acbr51-acbr52 link and '''42-Indor-Turbo''' for acbr52-acbr53 link.+
- +
-The configuration will be:+
- +
- CH106 CH42+
- acbr51 (ath0) - - - - - (ath0) acbr52 (ath1) - - - - - - (ath0) acbr53)+
- +
-====Wireless -> Wireless Security page====+
- +
-===WDS Parameters===+

Current revision

This page is now deprecated, instead see: WDS Linked router network