From DD-WRT Wiki

(Difference between revisions)
Jump to: navigation, search
Revision as of 15:13, 16 July 2006 (edit)
Phil6 (Talk | contribs)
← Previous diff
Revision as of 01:58, 15 February 2007 (edit) (undo)
Whiteboy (Talk | contribs)

Next diff →
Line 126: Line 126:
Just thought the translation is needed, since this is the English version of this WIKI. Sorry I could not do a better translation, but my Spanish is very poor. ... servant74 Just thought the translation is needed, since this is the English version of this WIKI. Sorry I could not do a better translation, but my Spanish is very poor. ... servant74
-[[Category:advanced HOWTO]] 
[[Category:English documentation]] [[Category:English documentation]]

Revision as of 01:58, 15 February 2007


This is an infant wiki! Help finish it!


Chillispot can be used for hotspot management. It requires a separate webserver to host the redirect url and a separate radius server (these may be installed on the same machine, of course).

copied from

Draft Configuration Guide for WRT54G using DD-WRT as a Hot Spot Please direct comments to

September 3, 2005

1. If OS on Linksys is some prior version of DD-WRT, telnet or SSH to router.

2. The following commands will erase the nvram. This means you must be able to connect to the router via the lan port of the WLAN port to do any further configuration .

mtd erase nvram

3. Connect to the router. The password is now admin

4. Upload the version of DD-WRT that you plan to use.

5. Repeat step 2.

6. Set the IP address on the WAN port to a static IP Address or somehow be able to know the IP address

7. Configure the router for remote management.

8. Reconnect to the router and upload the firmware. See below.

9. Reconnect to the router via the WAN port. This is required because you will now disable DHCP on the Main setting page.

10. Disable DHCP on the Main setting page

11. Reconnect to the router, set the output power to 250mw using the Wireless Advanced Settings page (This can be dangerous and is not completely neccesary.)

12. Reconnect to the router, disable Block Anonymous IMCP Requests and disable the Firewall

13. Reconnect to the router

a. enable SSH and telnet
b. enable reboot at 3:00 AM
c. configure Chillispot as follows
d. set Radius server 1 to be the ip address of a your primary radius server
e. set Radius server 2 to be the ip address of a your secondary radius server (use the same as server 1 if you only have one)
f. set dns server to be the ip address of a dns server
g. set radius secret to be your radius secret password
h. set dhcp interface to be LAN and WLAN
i. paste these entries into the additional Chillispot options:
radiuslisten the ipaddress set in step 6
radiusauthport 1812
radiusacctport 1813
macauth required if you want to use the mac address as the username
macsuffix @some_name - This will be the realm used in RADIUS authentication
macpasswd some value if you want to pass this parameter
radiusnasid some_name_with_no_spaces
net any net of your choosing. This is the net assigned to Wireless Clients
domain the domain name supplied by the Chillispot DHCP server
uamallowed any web address allowed without RADIUS authentication
dns2 the ip address of a dns server - optional
j. Make changes to radius listen port ip so that it matches the WAN port address set in step 6 above
k. Change the entry for net if desired. This is the DHCP network clients are assigned to when they connect

14. DO NOT enable Chillispot. Save setting and reboot router

15. Now enable Chillispot and reboot router

16. Go to Settings/Advanced Routing/Show Routing Tables. If Chillispot started, you should see the net specified in step 13(i).

17. Chillispot will not start unless it can see the dns server specified in step 13(f).

18. Other considerations

Update the RADIUS clients on your radius server

Chillispot info

If DD-WRT works with chillispot that is a key feature which should be built in and fully explained.

Does it? (If so I'll try to write it up when I get it working ;-)

If not, I won't have time to checkout DD-WRT.

Hotspot Newbie

September 3, 2005 Here is a draft configuration guide for using your WRT54G as a Hot Spot

I welcome your comments.


DD-WRT is basically a prepackaged version OpenWRT white russian that includes the chillispot software, among others. I have enabled the chillispot config on a linksys WRT54G successfully in conjunction with freeradius and apache located on a separate Debian linux installation in my DMZ. For kicks, I also have squid running on that Debian box. All works well except when I turn off ip forwarding in the hopes of just using squid in transparent proxy mode. In that case so far the connections drop from time to time. Anyway, the bottom line is "yes" it does work!


Es importante conciderar tambien que para usar Chillispot en DD-WRT es necesario tener los IP del servidor de chillispot los cuales le doy en este momento mas que todo si va ha configurar con el radius gratuito de chillispot:

radiusserver1 = espero que esto seha de ayuda a mis amigos de habla hispana

Rommel Salas --- WIFI

The [edited] babblefish version of Rommels' information is:

It is also important to consider that to use Chillispot in DD-WRT it is necessary to have the IP of the chillispot server which I give him at this point but that everything if it goes has to form with radius gratuitous of chillispot:

radiusserver1 = I hope that this is of aid to my friends of Hispanic speech

Just thought the translation is needed, since this is the English version of this WIKI. Sorry I could not do a better translation, but my Spanish is very poor. ... servant74