TP Link Archer C9

From DD-WRT Wiki

Revision as of 23:50, 25 May 2023 by Kernel-panic69 (Talk | contribs)
Jump to: navigation, search

Contents



Hardware Specifications

Feature v1 v2 v3 (EU) v4 v5
FCC ID TE7C9 TE7C9V2 TE7C9V4 TE7C9V5
Industry Canada ID 8853A-C9 8853A-C9V4
Power 12 VDC, 3.3 A 12 VDC, 3.3 A 12 VDC, 3.3 A 12 VDC, 3.3 A 12 VDC, 3.3 A
CPU Broadcom BCM4709 @1 GHz Broadcom BCM4709 @1 GHz Broadcom BCM4709A0 @1 GHz Broadcom BCM4709A0 @1 GHz Broadcom BCM4709A0 @1 GHz
Architecture ARM Cortex A9 (2 cores) ARM Cortex A9 (2 cores) ARM Cortex A9 (2 cores) ARM Cortex A9 (2 cores) ARM Cortex A9 (2 cores)
RAM / Flash (ROM) 128 MiB / 16 MiB 128 MiB / 16 MiB ? ? 256 MiB / 128 MiB
Switch Broadcom BCM4709 Broadcom BCM4709 Broadcom BCM4709A0 Broadcom BCM4709A0 Broadcom BCM4709A0
LAN/WAN ports 4 /1 @ 1 Gb/s 4 /1 @ 1 Gb/s 4 /1 @ 1 Gb/s 4 /1 @ 1 Gb/s 4 /1 @ 1 Gb/s
USB Ports 1x USB 2.0, 1x USB 3.0 1x USB 2.0, 1x USB 3.0 1x USB 2.0, 1x USB 3.0 1x USB 2.0, 1x USB 3.0 1x USB 2.0, 1x USB 3.0
JTAG internal
Serial internal, 4-pin header, 3.3V TTL internal, 4-pin header, 3.3V TTL internal, 4-pin header, 3.3V TTL internal, 4-pin header, 3.3V TTL internal, 4-pin header, 3.3V TTL
WI1 chip Broadcom BCM4360 Broadcom BCM4360 Broadcom BCM4360 Broadcom BCM4360 Broadcom BCM4360
WI1 protocols an+ac an+ac an+ac an+ac an+ac
WI1 MIMO config 3x3:3 3x3:3 3x3:3 3x3:3 3x3:3
WI1 antenna connector U.FL, RP-SMA U.FL, RP-SMA U.FL, RP-SMA U.FL, RP-SMA U.FL, RP-SMA
WI2 chip Broadcom BCM4360 Broadcom BCM4360 Broadcom BCM4360 Broadcom BCM4360 Broadcom BCM4360
WI2 protocols bgn bgn bgn bgn bgn
WI2 MIMO config 3x3:3 3x3:3 3x3:3 3x3:3 3x3:3
WI2 antenna connector U.FL, RP-SMA U.FL, RP-SMA U.FL, RP-SMA U.FL, RP-SMA U.FL, RP-SMA

The Archer C1900 is identical.

How to install DD-WRT

TP-Link Archer C9 v1

  • Ensure you have latest firmware from TP-Link
  • Download factory-to-ddwrt.bin from the tplink_archer-c9v1 directory from one of the links here.
  • Read New Build and model-specific threads to determine the stability of a given build.
  • Upload the dd-wrt firmware using the standard TP-Link UI and wait until router reboots
  • Do a normal reset or nvram erase via telnet/ssh (Do not 30/30/30 an ARM router!)
  • DO NOT UPDATE THE STOCK FIRMWARE TO A NEWER VERSION OR YOU MAY RISK A LOT OF EXTRA WORK. STICK TO STOCK BUILDS OLDER THAN 180125. 180125 will block your router from being able to update to any third party firmware. If your router is on this version or newer, you will need to follow this topic's instructions: Working Solution to Archer C9 V1 - software only, no serial

TP-Link Archer C9 v2

  • Ensure you have the latest firmware from TP-Link (tested with Archer C9(UN)_V2_160517)
  • Download factory-to-ddwrt.bin from the tplink_archer-c9v2 directory from one of the links here.
  • Read New Build and model-specific threads to determine the stability of a given build.
  • Upload the dd-wrt firmware using the standard TP-Link UI and wait until router reboots
  • Download the last appropriate dd-wrt firmware here
  • Upload the latest good webflash.bin build using the dd-wrt GUI found under Administration->Firmware Upgrade
  • DD-WRT v3.0-r30385 std (08/12/16) has been tested stable

TP-Link Archer C9 v3, v4

Device thread: TP-Link Archer C9 v3? (EU)

WARNING: Enabling JFFS bricks the router: "That seems to nuke all the way up to 0xFEFFFF in the SPI flash."

  • TheDoc's fix for bricked v3/v4 is here original (deprecated) fix is here.
  • Easier-to-read v4 de-brick thread is here

NOTE: There is a US-only version of the v4 that is not yet supported - Archer C9 V4 Unable to install firmware


TP-Link Archer C9 v5

This version is not currently supported. Doesn't look as if it will be anytime soon, either.
TP-Link Archer C9 (EU) V5 DD-WRT Support (NO GO)
a bit of a question about Archer C9 v5...
TPLINK Archer C9 v5 unlock the protection
TP-Link Archer C9 v5 config backup decryption key

Troubleshooting

Device Forum Thread: https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=282831

Bricked Router

Symptoms: all the LEDs are ON, and you can't access to UI

Follow these steps:

  • Switch off the router
  • Download a complete binary-image of firmware
  • Rename the downloaded firmware with the following name: archerc9v1_tp_recovery.bin or "archerc9v2_tp_recovery.bin" if you have a v2 router
  • Serve as TFTP server the renamed firmware on the following IP: 192.168.0.66
  • Switch on the router, holding the RESET button for 2-4 seconds
  • The firmware will be automatically downloaded and installed by the router

Symptoms: after the dd-wrt installation the MACs are changed!

Recovery Mode

The v3 CFE has a built-in Webpage Firmware Recovery mode for bricked routers: see TP-Link article.