TP Link Archer C8
From DD-WRT Wiki
(Difference between revisions)
Revision as of 15:08, 28 February 2018 (edit) Jeremywh7 (Talk | contribs) (add recovery for v3/v4) ← Previous diff |
Revision as of 15:10, 28 February 2018 (edit) (undo) Jeremywh7 (Talk | contribs) (add recovery for v3/v4) Next diff → |
||
Line 95: | Line 95: | ||
More information and alternate download locations: [[Firmware_FAQ#Where_do_I_download_firmware.3F|FAQ: Where do I download firmware?]] | More information and alternate download locations: [[Firmware_FAQ#Where_do_I_download_firmware.3F|FAQ: Where do I download firmware?]] | ||
- | ==Recovery== | + | ==Recovery Mode== |
The '''v3 and v4''' CFE has a built-in Webpage Firmware Recovery mode for bricked routers: see [https://www.tp-link.com/us/faq-1482.html TP-Link article].<br> | The '''v3 and v4''' CFE has a built-in Webpage Firmware Recovery mode for bricked routers: see [https://www.tp-link.com/us/faq-1482.html TP-Link article].<br> | ||
It may be possible to retrofit a v3 CFE onto v1/v2 models, '''but this is untested'''. | It may be possible to retrofit a v3 CFE onto v1/v2 models, '''but this is untested'''. |
Revision as of 15:10, 28 February 2018
There are four revisions of the Archer C8, with v1 and v2 supported by DD-WRT.
WARNING: There is no webrevert file nor other method to flash the C8 back to OEM firmware from DD-WRT!
Contents |
Hardware Specifications
FCC ID | TE7C8 |
---|---|
Industry Canada ID | 8853A-C8 |
Power | 12 VDC, 3.3 A |
CPU | Broadcom BCM4708 @800 MHz |
Architecture | ARM Cortex A9 (2 cores) |
RAM / Flash (ROM) | 128 MiB / 16 MiB |
Switch | Broadcom BCM4708 |
LAN/WAN ports | 4 /1 @ 1 Gb/s |
USB Ports | 1x USB 2.0, 1x USB 3.0 |
Serial | internal, 4-pin header, 3.3V TTL |
WI1 chip | Broadcom BCM4360 |
WI1 protocols | an+ac |
WI1 MIMO config | 3x3:3 |
WI1 antenna connector | U.FL, RP-SMA |
WI2 chip | Broadcom BCM4331 |
WI2 protocols | bgn |
WI2 MIMO config | 3x3:3 |
WI2 antenna connector | U.FL, RP-SMA |
- The unsupported v4 has 128 MiB flash but otherwise appears to have the same specifications.
Serial Boot Log info
From the OpenWRT wiki:
CFE memory report
Tot mem: 131072 KBytes CFE mem: 0x00F00000 - 0x00FCC810 (837648) Data: 0x00F414A8 - 0x00F418F4 (1100) BSS: 0x00F41900 - 0x00F66810 (151312) Heap: 0x00F66810 - 0x00FCA810 (409600) Stack: 0x00FCA810 - 0x00FCC810 (8192) Text: 0x00F00000 - 0x00F396D4 (235220)
MTD partitions
Creating 5 MTD partitions on "bcmsflash": 0x000000000000-0x000000040000 : "boot" 0x000000040000-0x000000240000 : "linux" 0x000000240000-0x000000ee0000 : "rootfs" 0x000000fe0000-0x000000ff0000 : "radio" 0x000000ff0000-0x000001000000 : "nvram"
WARNING: There is no webrevert file nor other method to flash the C8 back to OEM firmware from DD-WRT!
Installation
Tested: TP-Link Archer C8 V1 with TP-Link firmware: Archer C8_V1_150515
- Download DD-WRT firmware: factory-to-ddwrt.bin
- "Reset to factory defaults" via the OEM Archer GUI.
- Also from the Archer GUI, upload the factory-to-ddwrt.bin file.
- Wait at least one minute
- Access DD-WRT GUI at 192.168.1.1, set password, then GUI reset (Admin->Factory Defaults) again
- v2 should use the same process, and the 'v1' file.
- 33006 has also been tested.
- v3 is an EU model. There is one report of a v3 running DD-WRT, but with no details.
- No reports of a v4 (also EU). Warning: v4 has different flash size from v1-3.
More information and alternate download locations: FAQ: Where do I download firmware?
Recovery Mode
The v3 and v4 CFE has a built-in Webpage Firmware Recovery mode for bricked routers: see TP-Link article.
It may be possible to retrofit a v3 CFE onto v1/v2 models, but this is untested.
Notes
Forum model thread: Support for TP-Link Archer C8