TP Link Archer C8

From DD-WRT Wiki

(Difference between revisions)
Jump to: navigation, search
Revision as of 19:51, 27 February 2018 (edit)
Jeremywh7 (Talk | contribs)
(add C8)
← Previous diff
Revision as of 19:54, 27 February 2018 (edit) (undo)
Jeremywh7 (Talk | contribs)
m (fix link)
Next diff →
Line 91: Line 91:
*v2 should use the same process *v2 should use the same process
*[https://www.dd-wrt.com/phpBB2/viewtopic.php?p=1089503#1089503 33006] has also been tested. *[https://www.dd-wrt.com/phpBB2/viewtopic.php?p=1089503#1089503 33006] has also been tested.
-*There is [https://www.dd-wrt.com/phpBB2/viewtopic.php?t=300795 one report] of a v3 running DD-WRT as well, but with no details.+*There is [https://www.dd-wrt.com/phpBB2/viewtopic.php?t=311486 one report] of a v3 running DD-WRT as well, but with no details.
*No reports of a v4. '''Warning:''' v4 has different flash size from v1-3. *No reports of a v4. '''Warning:''' v4 has different flash size from v1-3.
More information: including [[Firmware_FAQ#Where_do_I_download_firmware.3F|alternate download locations]] More information: including [[Firmware_FAQ#Where_do_I_download_firmware.3F|alternate download locations]]

Revision as of 19:54, 27 February 2018

There are four revisions of the Archer C8, with v1 and v2 supported by DD-WRT.
WARNING: There is no webrevert file nor other method to flash the C8 back to OEM firmware from DD-WRT!

Contents

Hardware Specifications

FCC ID TE7C8
Industry Canada ID 8853A-C8
Power 12 VDC, 3.3 A
CPU Broadcom BCM4708 @800 MHz
Architecture ARM Cortex A9 (2 cores)
RAM / Flash (ROM) 128 MiB / 16 MiB
Switch Broadcom BCM4708
LAN/WAN ports 4 /1 @ 1 Gb/s
USB Ports 1x USB 2.0, 1x USB 3.0
Serial internal, 4-pin header, 3.3V TTL
WI1 chip Broadcom BCM4360
WI1 protocols an+ac
WI1 MIMO config 3x3:3
WI1 antenna connector U.FL, RP-SMA
WI2 chip Broadcom BCM4331
WI2 protocols bgn
WI2 MIMO config 3x3:3
WI2 antenna connector U.FL, RP-SMA
  • The unsupported v4 has 128 MiB flash, otherwise appears to have the same specifications.


Serial Boot Log info

From the OpenWRT wiki:

CFE memory report

   Tot mem: 131072 KBytes
   CFE mem: 0x00F00000 - 0x00FCC810 (837648)
   Data: 0x00F414A8 - 0x00F418F4 (1100)
   BSS: 0x00F41900 - 0x00F66810 (151312)
   Heap: 0x00F66810 - 0x00FCA810 (409600)
   Stack: 0x00FCA810 - 0x00FCC810 (8192)
   Text: 0x00F00000 - 0x00F396D4 (235220)

MTD partitions

   Creating 5 MTD partitions on "bcmsflash":
   0x000000000000-0x000000040000 : "boot"
   0x000000040000-0x000000240000 : "linux"
   0x000000240000-0x000000ee0000 : "rootfs"
   0x000000fe0000-0x000000ff0000 : "radio"
   0x000000ff0000-0x000001000000 : "nvram"

WARNING: There is no webrevert file nor other method to flash the C8 back to OEM firmware from DD-WRT!

Installation

Tested: TP-Link Archer C8 V1 with TP-Link firmware: Archer C8_V1_150515.

  1. Download DD-WRT firmware: factory-to-ddwrt.bin
  2. "Reset to factory defaults" via the OEM Archer GUI.
  3. Also from the Archer GUI, upload the factory-to-ddwrt.bin file.
  4. Wait at least one minute
  5. Access DD-WRT GUI at 192.168.1.1, set password, then GUI reset (Admin->Factory Defaults) again
  • v2 should use the same process
  • 33006 has also been tested.
  • There is one report of a v3 running DD-WRT as well, but with no details.
  • No reports of a v4. Warning: v4 has different flash size from v1-3.

More information: including alternate download locations

Notes

Forum model thread: Support for TP-Link Archer C8