Simple Network Management Protocol
From DD-WRT Wiki
Revision as of 19:00, 9 July 2006 (edit) BrainSlayer (Talk | contribs) m (Reverted edit of 201.78.56.136, changed back to last version by Gerrys) ← Previous diff |
Revision as of 20:56, 11 July 2006 (edit) (undo) Bluse-Blue (Talk | contribs) Next diff → |
||
Line 58: | Line 58: | ||
In "Parameters", type in the IP of the router and the read and write community passwords. Press "Start" and you should see the bottom status say something like "Sysinfo variables OK". Next, go to the "MBrowser" tab and put ".1.3.6.1.4.1.2021.8.1" in the second entry box (it probably says ".1"). Press "Start" and you should see a list of values pop into the lower output screen. You will see your configuration variables, then a list of numbers in the values side. The first 3 numbers will be "0", then your values will show up. First is your "Rate", then each of your RSSI values that you entered above. | In "Parameters", type in the IP of the router and the read and write community passwords. Press "Start" and you should see the bottom status say something like "Sysinfo variables OK". Next, go to the "MBrowser" tab and put ".1.3.6.1.4.1.2021.8.1" in the second entry box (it probably says ".1"). Press "Start" and you should see a list of values pop into the lower output screen. You will see your configuration variables, then a list of numbers in the values side. The first 3 numbers will be "0", then your values will show up. First is your "Rate", then each of your RSSI values that you entered above. | ||
+ | ==Known OID´s via SNMP== | ||
+ | |||
+ | This should get all the available OIDS | ||
+ | |||
+ | CPU is | ||
+ | .1.3.6.1.4.1.2021.10.1.3.1 (1 min av) | ||
+ | .1.3.6.1.4.1.2021.10.1.3.2 (5 min av) | ||
+ | .1.3.6.1.4.1.2021.10.1.3.3 (10 min av) | ||
+ | |||
+ | For tcp there are many counters | ||
+ | I use tcp active an passive connections at | ||
+ | .1.3.6.1.2.1.6.5.0 and .1.3.6.1.2.1.6.6.0 | ||
+ | |||
+ | Uptime | ||
+ | 1.3.6.1.2.1.2.2.1.10.5 | ||
==Using SNMP for bandwith monitoring== | ==Using SNMP for bandwith monitoring== |
Revision as of 20:56, 11 July 2006
Contents |
Introduction
The Simple Network Management Protocol (SNMP) is a protocol for monitoring of network-attached devices for any conditions that warrant administrative attention.
Wireless Rate Via SNMP
This particular setup is for creating new SNMP values that monitor the Rate setting of the wireless and the RSSI values of specific clients/WDS. I borrowed some of this code and modified it to work with v23. Someone said this came from the Sveasoft forums. Assumes use of DD-WRT v23.
Tools: Getif (SNMP MIB browser)
1) Turn on SNMP in DD-WRT (Administration->Services)
2) Turn on JFFS and clean it (Administration->Management)
3) Log in via SSH and create the following scripts:
/jffs/snmpd/wlrate:
#!/bin/sh /usr/sbin/wl rate |/usr/bin/cut -b 9-10
/jffs/snmpd/wlrssi1:
#!/bin/sh /usr/sbin/wl rssi <mac_address_of_client_or_wds> | /usr/bin/cut -b 10-11
You can repeat wlrssi1 multiple times for each client or WDS you want to monitor. Just increment the number.
Next, type the following into the command-line:
nvram set snmpd_conf="syslocation <your_location> syscontact <your_email> sysname <your_system_name> rocommunity <your_password> rwcommunity <your_other_password> exec Rate /jffs/snmpd/wlrate exec RSSI-CLIENT1 /jffs/snmpd/wlrssi1 " nvram commit reboot
Again, repeat the "RSSI-CLIENT1" line if you have more than 1 client to monitor (incrementing the number, of course).
Test the settings with Getif. You will need to look for .1.3.6.1.4.1.2021.8.1 in the "MBrowser" screen.
Steps:
In "Parameters", type in the IP of the router and the read and write community passwords. Press "Start" and you should see the bottom status say something like "Sysinfo variables OK". Next, go to the "MBrowser" tab and put ".1.3.6.1.4.1.2021.8.1" in the second entry box (it probably says ".1"). Press "Start" and you should see a list of values pop into the lower output screen. You will see your configuration variables, then a list of numbers in the values side. The first 3 numbers will be "0", then your values will show up. First is your "Rate", then each of your RSSI values that you entered above.
Known OID´s via SNMP
This should get all the available OIDS
CPU is .1.3.6.1.4.1.2021.10.1.3.1 (1 min av) .1.3.6.1.4.1.2021.10.1.3.2 (5 min av) .1.3.6.1.4.1.2021.10.1.3.3 (10 min av)
For tcp there are many counters I use tcp active an passive connections at .1.3.6.1.2.1.6.5.0 and .1.3.6.1.2.1.6.6.0
Uptime 1.3.6.1.2.1.2.2.1.10.5
Using SNMP for bandwith monitoring
You can also use SNMP for bandwith monitoring by using programs like MRTG or PRTG Traffic Graphers.
The routers SNMP traffic layout:
(___br0___) / | \ \_ \____ / | \ \__ \_____ / | \ \ \ | [0] [1] [2] [3] [4] | | [wlan] | |vlan1 ---- vlan0 ----- | | | | WAN LAN | | WLAN | | | | | |Internet 1 2 3 4 | | WLAN | <-- label +---------------------------+ +--------+ ethernet switch wireless eth0 (cpu port 5) eth1