Serial port pinouts

From DD-WRT Wiki

(Difference between revisions)
Jump to: navigation, search
Revision as of 12:56, 3 January 2011 (edit)
Leangjia (Talk | contribs)

← Previous diff
Revision as of 19:14, 3 January 2011 (edit) (undo)
Winmedia (Talk | contribs)
(Dlink DIR-300 revb)
Next diff →
Line 112: Line 112:
==Dynex DX-NRUTER== ==Dynex DX-NRUTER==
[[Image:dynex_nruter.png]] [[Image:dynex_nruter.png]]
 +
 +== D-Link DIR-615 D3==
 +The serial port runs at 57600 baud, 8 bits. Voltage levels are +3.3V TTL logic. RX is pulled up.
==Dlink DIR-300 revb== ==Dlink DIR-300 revb==
NOTE: RevB is completely different hardware, based on Ralink RT3050 SoC. The serial port runs at 57600 baud, 8 bits, no parity, 1 stop bit using ANSI terminal emulation. Levels are not RS232 voltage levels, but +3.3V TTL logic. Use an interface converter chip (Max232/Max3232/DS275 etc.) to connect to standard RS-232. NOTE: RevB is completely different hardware, based on Ralink RT3050 SoC. The serial port runs at 57600 baud, 8 bits, no parity, 1 stop bit using ANSI terminal emulation. Levels are not RS232 voltage levels, but +3.3V TTL logic. Use an interface converter chip (Max232/Max3232/DS275 etc.) to connect to standard RS-232.
 +
==Dlink DIR-300 revb (Chinese) == ==Dlink DIR-300 revb (Chinese) ==
注意: RevB硬件结构是完全不一样的,使用的是雷凌RT3050芯片。串口使用的是57600波特率,配置为n,8,1,电平3.3V的TTL逻辑电平并非RS232的电压,所以需要通过电平转换芯片(Max232/Max3232/DS275 etc.)然后连接到RS-232上。[[Image:Dlink-DIR300revb.JPG]] 注意: RevB硬件结构是完全不一样的,使用的是雷凌RT3050芯片。串口使用的是57600波特率,配置为n,8,1,电平3.3V的TTL逻辑电平并非RS232的电压,所以需要通过电平转换芯片(Max232/Max3232/DS275 etc.)然后连接到RS-232上。[[Image:Dlink-DIR300revb.JPG]]

Revision as of 19:14, 3 January 2011

If anyone has any photos or diagrams, please upload them to the wiki (NOT link to an external image) and add them to this page.

Contents

For those interested: (--------- is nearest board edge)

Buffalo WBR2-G54(S)

----------
J5
o gnd
o vcc
o rx
o tx

Motorola WR850G v2 /v3

| tx o o vcc  RJP1
|    o o
|    o o gnd
| rx o o
|    o

Buffalo WLA2-G54C

| tx o o
|    o o vcc
|    o o gnd
| rx o o
|    o
---------

Buffalo WHR-G54S

Connector RJP1

 tx o o      |
    o o vcc  |
    o o gnd  |
 rx o o      |
    o        |
-------------

The serial port runs at 115200 baud, 8 bits, no parity, 1 stop bit using ANSI terminal emulation.

Buffalo WHR-HP-G54

Connector J1

             |
      rx o   |
      tx o   |
     gnd o   |
     vcc o   |
-------------

The serial port runs at 115200 baud, 8 bits, no parity, 1 stop bit using ANSI terminal emulation. Levels are not RS232 voltage levels, but +3.3V TTL logic. Use level shifter (Max232/Max3232/DS275 etc.) to correct this. Also a USB to serial phone cable will work in most cases. A cable with a Prolific 2303 works fine to access the router as a device (Eg. to get a bootloader commandline). It does not work in host mode to control USB devices. The VCC pin puts out 3.3V.

Image:BuffaloWHR-HP-G54_serial_small.jpg

Buffalo WHR-G125

Connector J1

|            
|     rx  o   
|     tx  o   
|    gnd o   
|    vcc o 
-------------

The serial port runs at 115200 baud, 8 bits, no parity, 1 stop bit using ANSI terminal emulation. Levels are not RS232 voltage levels, but +3.3V TTL logic. Use level shifter (Max232/Max3232/DS275 etc.) to correct this. Also a USB to serial phone cable will work in most cases. A cable with a Prolific 2303 works fine.

Linksys WRT-54G(S,L)

JP1 or JP2 (on newer models)

vcc 1-2 vcc |
tx1 3-4 tx0 |
rx1 5-6 rx0 |
... 7-8 ... |
gnd 9-10 gnd |

(numbering as shown on the PCB at JP2 in my WRT54GL v1.1, Rockus 10:42, 25 May 2008 (CEST))


below numbering shown on my WRT-54GS V1 with JP1 busstopgangsta 11.11.2008 00:16 GMT+1 Image:Wrt54gs_v1_serial.JPG

Linksys WRT110

Image:Linksys_WRT110_serial_pinout.png

Linksys WRT-350N v 2.0

J5

vcc o
tx1 o 
rx1 o 
gnd o

Asus WL-500 deluxe

|       o o
| gnd o o vcc
| tx1 o o tx0
| rx1 o o rx0   
|        J5

Image:Wiki_serial_asus_wl500g.d.jpg

Sparklan WX6615GT

|    o
| gnd o o rx
| gnd o o 
| vcc o o 
| vcc o o tx   
|        J5

Airlink AR430W

Image:Ar430wserial.jpg

Dynex DX-NRUTER

Image:dynex_nruter.png

D-Link DIR-615 D3

The serial port runs at 57600 baud, 8 bits. Voltage levels are +3.3V TTL logic. RX is pulled up.

Dlink DIR-300 revb

NOTE: RevB is completely different hardware, based on Ralink RT3050 SoC. The serial port runs at 57600 baud, 8 bits, no parity, 1 stop bit using ANSI terminal emulation. Levels are not RS232 voltage levels, but +3.3V TTL logic. Use an interface converter chip (Max232/Max3232/DS275 etc.) to connect to standard RS-232.

Dlink DIR-300 revb (Chinese)

注意: RevB硬件结构是完全不一样的,使用的是雷凌RT3050芯片。串口使用的是57600波特率,配置为n,8,1,电平3.3V的TTL逻辑电平并非RS232的电压,所以需要通过电平转换芯片(Max232/Max3232/DS275 etc.)然后连接到RS-232上。Image:Dlink-DIR300revb.JPG

TP-Link TL-WR941ND ver.3

Connector P1 (see picture)

                |
      tx o    |
      rx o    |
     gnd o   |
     vcc o   |

Login: "ap71"

Optional login: "root" Password: "5up"

The serial port runs at 115200 baud, 8 bits, no parity, 1 stop bit using ANSI terminal emulation. Levels are not RS232 voltage levels, but +3.3V TTL logic. Use level shifter (Max232/Max3232/DS275 etc.) to correct this. Also a USB to serial phone cable will work in most cases. A cable with a Prolific 2303 works fine. You have to short R356, if not, the TX will not going to work. Image:Serial_if.jpg

External Links

WRT160NL

Image:DD-WRT160NL-SerialPort.jpg