Recover from a bad flash

From DD-WRT Wiki

Revision as of 00:42, 8 October 2006 by AycheKay (Talk | contribs)
Jump to: navigation, search

So, you're afraid you've bricked your router. Don't worry, there are a number of things you can try to get your router working again before giving up and living with the fact that your router is now a paperweight.

The WRT54G Revival Guide includes step-by-step instructions how to get your Linksys router working again.

Contents

WRT54G Revival Guide

WRT54G Revival Guide

NOTE: The Revival Guide is somewhat dated.

Linksys Firmware

If you cannot find a Firmware Auto-Upgrade utility at the Linksys Download Page, use a Setup Wizard as an alternative from other Linksys router (make sure to use your router's firmware).

Confirming Network Connection

If pinging 192.168.1.1 does not work, check the IP Address of your computer and make sure it is assigned an IP address in the subnet of the router IP. For simplicity sake you can assume "192.168.1.x" is good. If you do not have a good IP, the DHCP Server might not be working. So set your IP manually to something like 192.168.1.77 with 192.168.1.1 as your gateway and then try pinging the router again.

Recovering WRT54G

Power the router on with a continuous ping running in a command window. You should see at least some seconds, at least 2-3 pings, where it responds to ping of 192.168.1.1 address. Do this several times to be sure. If it does you have good chance of simple recovery. Especially if previous firmware set the boot_wait variable to on, the router pauses even longer than normal during bootup to accept a recovery flash. All you need to do is provide a firmware to it via TFTP during this window of time.

So prepare your PC, firmware file and TFTP software and play with the timing of powering it on and starting the TFTP session just after applying power. If you try it a number of times (at least 10) you will probably rescue the router with no fuss!

If the Linksys-approved method does not work for you, the Revival Guide includes a second technique that involves snapping open the plastic case of the router and using a small metal tool (or paper-clip) to "short" two particular "pins" on the circuit board. It is quite clear that this carries risk of permanently damaging your flash via static discharge, and should be a measure of EXTREME last resort, not the first thing to try. You can very likely recover from a bad flash WITHOUT opening the router if you have some patience with the TFTP technique.

There's also a collection of pointers and tips on how to recover from a bad flash at the external link location, but most of the information in that forum seems to have been collected into the WRT54G Revival Guide. So far this is just a starter wiki. If someone could move the important parts into this wiki, that'd be great. Probably organize it by recovery methods and list variations of each method below the method, or something.

External Links

The Wrt54g Revival Guide - Excellent step-by-step instructions (with color photos)

Note that contrary to the instructions, some Linksys cases are secured by screws. Just remove the two front rubber feet to get access to the screws.

How-To: Recover from a bad firmware flash. - Question and Answer Forum 948398761295253634222718

Reviving the Buffalo WHR-G54S

If you have already tried pinging the Buffalo continuously through hard and soft resets, unplugging, plugging and any combination thereof, then you will need to open up the device in order to revive it, similar in practice to the WRT54G Revival Guide Method #3.

  1. Unplug the router, and slide off the side trim panels. One will be covering a torx screw.
  2. Undo the screw and open up the router.
  3. With the router unplugged, plug a patch cable into one of the 4 LAN ports on your router and plug the other end into a computer.
  4. Configure your network card on your computer with a static IP address: IP: 192.168.11.2, NETMASK: 255.255.255.0, no gateway.
  5. Run a the ping command in a terminal or command prompt. In Linux: "ping 192.168.11.1". In Windows "ping -t 192.168.11.1" so that it doesn't stop trying to ping after 4 pings.
  6. Locate pin 12 on the flash memory chip. It is the 12th pin counterclockwise from the dimple in the surface of the chip. See the specs for this chip here.
  7. Short this pin to ground (bare solder around antennas, screw points).
  8. While holding the screwdriver there, plug in the power and watch your ping screen. You should see the pings starting to succeed.
  9. Remove the screwdriver and the pings should continue.
  10. Now use the tftp method to rewrite the firmware.