Optware
From DD-WRT Wiki
Contents |
Introduction
With the latest DD-WRT v23 SP2, it is possible to install Optware packages from NSLU2-Linux project. This port of Optware is tailored for DD-WRT and extends the router to full feature linux if enough storage (jffs, SD/MMC Card, USB) is provided for packages.
The main feature of this package is that it installs all required files under /opt with 600+ ported applications. With buildroot toolchain, system library independence is also added. This means that packages now depend on /opt/lib/uClibc.so and dynamic loader also in /opt/lib with separate /opt/etc/ld-opt.so.conf for custom .so cache. Applications are built with wchar and locale support which makes uClibc library somewhat greater than other uClibc packages, but still far smaller than glibc based aplications.
Buildroot toolchain features:
- GCC 4.1.1
- uClibc 0.9.28 with many patches
- uClibc++ 0.2.2
- Native POSIX Threads Library (NPTL) Support for uClibc
Some packages (perl, python, Transmission, buildroot, ...) are so memory hungry that swap is needed for normal operation. Buildroot package or optware-devel meta package provides complete development toolchain for compiling programs on router itself with gcc, gdb, make, g++, svn, ...
Basic preparation of /jffs is required (enable, clean). On WRT54GS there is room for some aplications. SD card (/mmc) may give enough space for many applications. For testing purposes also smbmount can be used. It should be noted that writable /jffs partition must be provided as /bin/ipkg script requires it to save some data there. If a non /jffs filesystem is available, it is recommended to unmount /jffs and then mount eg. mmc in place of /jffs.
Example scenario of installing some packages on WRT54GS
Preparing /jffs for /opt
First step is to prepare /opt mount point for Optware.
~ # mkdir /jffs/opt ~ # mount -o bind /jffs/opt /opt
Installing ipkg-opt and uclibc-opt
First we will install uClibc library required by all packages and better ipkg-opt packager. Recommended way for installing basic two packages is with installation script that will also check for possible network problems and /opt directory availability. To install (or reinstall) issue the following two commands:
wget http://pastebin.ca/raw/328107 -O - | tr -d '\r' > /tmp/optware-install.sh sh /tmp/optware-install.sh
Output should look like:
Checking system config ... Using 192.168.1.1 as default gateway. Using the following nameserver(s): nameserver 192.168.1.30 Warning: local nameserver is different than gateway! Check config or enter: sed -i s/192.168.*/192.168.1.1/ /tmp/resolv.conf to correct this. Installing package uclibc-opt_0.9.28-12_mipsel.ipk ... Connecting to ipkg.nslu2-linux.org[140.211.166.82]:80 uclibc-opt_0.9.28-12 100% |***********************************************| 832 KB 00:00:00 ETA Updating /opt/etc/ld.so.cache /opt/sbin/ldconfig: can't create /opt/etc/ld.so.cache~ (No such file or directory) Installing package ipkg-opt_0.99.163-9_mipsel.ipk ... Connecting to ipkg.nslu2-linux.org[140.211.166.82]:80 ipkg-opt_0.99.163-9_ 100% |***********************************************| 75896 00:00:00 ETA Downloading http://ipkg.nslu2-linux.org/feeds/optware/ddwrt/cross/stable/Packages.gz Inflating http://ipkg.nslu2-linux.org/feeds/optware/ddwrt/cross/stable/Packages.gz Updated list of available packages in /opt/lib/ipkg/lists/optware Successfully terminated. Installing uclibc-opt (0.9.28-12) to /opt/... Downloading http://ipkg.nslu2-linux.org/feeds/optware/ddwrt/cross/stable/uclibc-opt_0.9.28-12_mipsel.ipk package uclibc-opt suggests installing ipkg-opt Configuring uclibc-opt Updating /opt/etc/ld.so.cache Successfully terminated. Installing ipkg-opt (0.99.163-9) to /opt/... Downloading http://ipkg.nslu2-linux.org/feeds/optware/ddwrt/cross/stable/ipkg-opt_0.99.163-9_mipsel.ipk Configuring ipkg-opt Successfully terminated.
Besides pre installing fundamental packages, there are also manual installation instuctions. This are now somewhat deprecated due to large number of user miss-understandings.
/opt backup
Now we have prepared /opt for adding more packages. We can also create backup of the whole /opt tree in case of router upgrade, to give preinstalled /opt to a friend or just safety backup. We will create such backup with
~ # tar czf /tmp/opt-backup.tar.gz /opt
Destination for /tmp/opt-backup.tar.gz should be large enough! Beware that /tmp is RAM. Destination should be disk or remote smbfs partition. Extracting /opt backup could be:
cd / rm -rf opt/* tar xvzf /tmp/opt-backup.tar.gz
If /opt space is tight and no packages requiring libstdc++ will be used (like Amule) then removing this large shared library is recommended
~ # rm /opt/lib/libstdc\+*
will remove
/opt/lib/libstdc++.so /opt/lib/libstdc++.so.6 /opt/lib/libstdc++.so.6.0.8
ipkg-opt downloads packages into /opt directory and erases them after installing. If you have enough free RAM and /jffs only then adding --tmp-dir /tmp is recommended instead of default /opt
Search PATH
Adding /opt/bin to search PATH will save us from tedious typing of /opt/bin for each command from /opt/bin. For running applications from /opt tree search path should be expanded with
~# export PATH=/opt/bin:/opt/sbin:$PATH
Now we can install any package from a list of available packages.
~# ipkg-opt list | more
or less or this Quick list of Optware packages
Installing ncFTP client
We want to get list of packages containing name ftp
~ # /opt/bin/ipkg-opt list '*ftp*' atftp - 0.7-6 - Advanced TFTP server and client ftpcopy - 0.6.7-3 - A simple FTP client written to copy files or directories (recursively) from a FTP server. ftpd-topfield - 0.6.10-2 - FTPD for the Topfield TF5000PVRt ncftp - 3.2.0-2 - Nice command line FTP client proftpd - 1.3.0a-1 - Highly configurable FTP server with SSL-TLS tftp-hpa - 0.45-1 - A tftp package tnftp - 20050625-1 - tnftp (formerly lukemftp) is what many users affectionately call the enhanced ftp client in NetBSD. tnftpd - 20061217-2 - tnftpd (formerly lukemftpd) is a port of the NetBSD FTP server to other systems. vsftpd - 2.0.1-7 - ftp daemon with an emphasis on speed and security Successfully terminated.
For example we will install ncFTP client with:
~ # /opt/bin/ipkg --tmp-dir /tmp install ncftp Installing ncftp (3.2.0-2) to /opt/... Downloading http://ipkg.nslu2-linux.org/feeds/optware/ddwrt/cross/stable/ncftp_3.2.0-2_mipsel.ipk Installing ncurses (5.6-1) to /opt/... Downloading http://ipkg.nslu2-linux.org/feeds/optware/ddwrt/cross/stable/ncurses_5.6-1_mipsel.ipk Configuring ncftp Configuring ncurses Successfully terminated.
and run it
~ # /opt/bin/ncftp ftp.si.debian.org NcFTP 3.2.0 (Aug 05, 2006) by Mike Gleason (http://www.NcFTP.com/contact/). Copyright (c) 1992-2005 by Mike Gleason. All rights reserved. Connecting to 164.8.6.249... CAMTP Debian mirror [ftp.si.debian.org] Logging in... Anonymous access granted, restrictions apply. Logged in to ftp.si.debian.org. ncftp / > ls backports/ debian-cd/ debian-sl/ openoffice/ debian/ debian-non-US/ favicon.ico robots.txt ncftp / > bye You have not saved a bookmark for this site. Would you like to save a bookmark to: ftp://ftp.si.debian.org Save? (yes/no) yes Enter a name for this bookmark, or hit enter for "si": debian Bookmark "debian" saved.
Always check available size of your /opt partition with
~ # df Filesystem 1k-blocks Used Available Use% Mounted on /dev/root 1984 1984 0 100% / /dev/mtdblock/4 5248 3860 1388 74% /jffs /dev/mtdblock/4 5248 3860 1388 74% /opt
Remove unneeded packages with
~ # /opt/bin/ipkg remove ncftp Removing package ncftp from /opt/... Successfully terminated.
You will notice that ncurses as depended package will not get removed. To correct this issue
~ # /opt/bin/ipkg remove ncurses Removing package ncurses from /opt/... Successfully terminated.
unless some other package require this package.
Installing torrent client
Of course there are many more packages which should run on router without a problem. All binaries have built in /opt/lib search path and there should be no problem with libraries clash like problems with OpenWRT packages. All packages have builtin package dependencies and will install required libraries automagically. Lets show this on installing torrent clients:
~ # /opt/bin/ipkg -t /tmp install enhanced-ctorrent Installing enhanced-ctorrent (dnh2.2-6) to /opt/... Downloading http://ipkg.nslu2-linux.org/feeds/optware/ddwrt/cross/stable/enhanced-ctorrent_dnh2.2-6_mipsel.ipk Installing libuclibc++ (0.2.2-4) to /opt/... Downloading http://ipkg.nslu2-linux.org/feeds/optware/ddwrt/cross/stable/libuclibc++_0.2.2-4_mipsel.ipk Installing openssl (0.9.7l-3) to /opt/... Downloading http://ipkg.nslu2-linux.org/feeds/optware/ddwrt/cross/stable/openssl_0.9.7l-3_mipsel.ipk Configuring enhanced-ctorrent Configuring libuclibc++ Configuring openssl Successfully terminated.
We will not show running example for this clients as normally huge amount of storrage is required.
Another torrent client with WWW interface is Transmission. Installing is simple as
~ # /opt/bin/ipkg install transmission Installing transmission (0.6+r1378-5) to /opt/... Downloading http://ipkg.nslu2-linux.org/feeds/optware/ddwrt/cross/stable/transmission_0.6+r1378-5_mipsel.ipk package transmission suggests installing gnuplot package transmission suggests installing logrotate Installing openssl (0.9.7l-3) to /opt/... Downloading http://ipkg.nslu2-linux.org/feeds/optware/ddwrt/cross/stable/openssl_0.9.7l-3_mipsel.ipk Configuring openssl Configuring transmission Please note that /opt/etc/init.d/S80busybox_httpd is installed for running CGI interface at http://localhost:8008/cgi-bin/transmission.cgi See instructions for daemon and WWW interface in /opt/share/doc/transmission Configure daemon with /opt/etc/transmission.conf Successfully terminated.
Besides simple command line transmissioncli client like enhanced-ctorrent, there is also possibility to run several torrents in daemon mode (background mode) with WWW page as interface watching daemon state and controlling its work.
After creating directories with
~ # mkdir /opt/torrent ~ # mkdir /opt/torrent/source ~ # mkdir /opt/torrent/work ~ # mkdir /opt/torrent/target
we will configure transmisison itself by editing /opt/etc/transmisison.conf by using
~ # sed -i -e 's|/tmp/harddisk|/opt|' /opt/etc/transmission.conf
to change default path from /tmp/harddisk to /opt. Also user should be changed from admin to root. After changing config transmission_watchdog should be run every half an hour with cron. We will start it manually and check if it is running
~ # /opt/sbin/transmission_watchdog ~ # ps |grep transmission 10621 root 808 S transmissiond -p 65534 -w 300 -u -1 -d -1 -i /opt/var 10624 root 808 S transmissiond -p 65534 -w 300 -u -1 -d -1 -i /opt/var 10625 root 808 S transmissiond -p 65534 -w 300 -u -1 -d -1 -i /opt/var 10626 root 808 R transmissiond -p 65534 -w 300 -u -1 -d -1 -i /opt/var
We will configure http server to show the startup page at port 8008. Although dd-wrt SP2 uses /opt/sbin/httpd for its WEB interface, this httpd server cannot be reused as it has serioius problems running CGI programs and showing index.html files.
For public trackers CGI interface provides 'Fetch' button which downloads .torrent file into /opt/torrent/source directory. Private trackers use passkey which means that .torrent file should be saved with browser itself.
After seeing .torrent file int Queued list, one can press Watchdog button to force queue processing. This will move .toorent file from source into work directory and notify daemon for the change to start processing the file. After download finishes, transmission_watchdog will automaticly move torrent from work to target. Meanwhile, user can pres Update button to see status of active torrents.
Besides transmissiond two other daemons are required for normal queue processing. Both are provided by dd-wrt if enabled. Cron is enabled under Admin control panel. Syslogd is enabled under Services tab.
Cron should regulary run /opt/sbin/transmisison_watchdog with sample /opt/etc/crontab
*/30 * * * * root /opt/sbin/transmission_watchdog
Visit CRON page to see where this line should be included. I recommend
cat /opt/etc/crontab >> /tmp/crontab
at startup,
Syslog will collect cumulative reports from transmisisond and CGI will show it when Log or Update is pressed. If gnuplot is installed then also transfer graph is showed when Log is pressed. SYSLOG line in /opt/etc/transmisison.conf must be changed to
SYSLOG=/var/log/messages
to be able to see Log messages from daemon when Log button is pressed.
Opening default listening port 65534 for Transmission is another required task which can be solved by DD-WRT control panel or adding
/usr/sbin/iptables -I INPUT 1 -p tcp --dport 65534 -j logaccept
to startup file.
Installing Throttling HTTP server
For our purposes thttpd WEB server will handle most requirements like browsing directories and runing CGI program located at /opt/share/www/cgi-bin/transmission.cgi
~ # /opt/bin/ipkg install thttpd Installing thttpd (2.25b-4) to /opt/... Downloading http://ipkg.nslu2-linux.org/feeds/optware/ddwrt/cross/stable/thttpd_2.25b-4_mipsel.ipk Configuring thttpd To complete the installation, you must edit /opt/etc/thttpd.conf, and then run /opt/etc/init.d/S80thttpd to start thttpd. Successfully terminated.
Edit /opt/etc/thttpd.conf with vi (or nano) and add cgipat, change user to root, change port to 8008 to see the following contents:
dir=/opt/share/www port=8008 user=root nochroot nosymlink novhost logfile=/var/log/thttpd.log pidfile=/var/run/thttpd.pid cgipat=cgi-bin/*
Manually start thttpd with
~ # /opt/etc/init.d/S80thttpd start
After that you will be able to see default index.html page at http://192.168.1.1:8008/ assuming that your router is at 192.168.1.1 . There is also link to CGI page http://192.168.1.1:8008/cgi-bin/transmission.cgi which is preaty empty with several buttons for controlling daemon.
Installing Samba
It looks like Samba 3 is too big for all "swapless" routers. For this reason I have prepared Samba 2 packages with Samba Web Admin Tool (SWAT) which will ease config and admin for samba newcomers. SWAT interface looks like:
Installation and running samba 2 is done out of the box by the following commands:
/opt/bin/ipkg update /opt/bin/ipkg remove samba /opt/bin/ipkg install samba2 /opt/bin/ipkg install xinetd /opt/etc/init.d/S10xinetd start /opt/etc/init.d/S80samba start
Point your browser to http://192.168.1.1:901/ to administer samba. Installation of xinetd is optional and it is not required if one wants to manually edit /opt/etc/samba/smb.conf
Running at startup
DD-WRT provides user startup files in /jffs/etc/config . To create optware startup file do
~ # mkdir /jffs/etc ~ # mkdir /jffs/etc/config ~ # vi /jffs/etc/config/optware.startup
with the following contents
#!/bin/sh mount -o bind /jffs/opt /opt if [ -d /opt/etc/init.d ]; then for f in /opt/etc/init.d/S* ; do [ -x $f ] && $f start done fi
and mark it as executable with
~ # chmod +x /jffs/etc/config/optware.startup
After reboot this file will be executed. I recommed first trying it manually
~ # /jffs/etc/config/optware.startup
Remarks
- DD-WRT provided /bin/ipkg is not full feature ipkg but it can do the job for installing ipkg-opt. It could also be used for installing other packages, but this is not recommended any more.
- Using samba share for /opt is not easy as there is no notion for symbolic links on SMB. This is most problematic for symbolic links on shared libraries. Rewriting "ln" to act as a script and put it on the head of search path could be used to copy instead of link. Possibility of mounting filesystem in a file as a loop device on a samba share is not yet verified.
- DD-WRT kernel lacks many "server" features like NFS, NBD support, ... Provided samba, mysql, thttp-php and other applications can do the job if enough space is provided. This means that external storage is required for memory hungry applications. Experience from nslu2 and Oleg firmware showed that 512MB swap space is recommended if external USB hard disk is available. See USB page for instructions how to initialize USB kernel modules and harddisk.
- Optware for DD-WRT is beta-stage feature. Report problems and suggestions in DD-WRT forum under Optware.
- For instuctions on some other packages look at http://www.nslu2-linux.org/wiki/Unslung/Packages
- Package feed will eventually change to official NSLU2 package feeds
- Optware package tracking and repository access
- There is also posibility to install Optware packages under Oleg, X-wrt or OpenWRT Whiterussian firmware. See instructions on http://www.nslu2-linux.org/wiki/FAQ/Optware-uClibcBuild