Netgear WNR2000V2

From DD-WRT Wiki

(Difference between revisions)
Jump to: navigation, search
Revision as of 09:39, 3 December 2014 (edit)
Malachi (Talk | contribs)
m
← Previous diff
Revision as of 20:59, 24 March 2015 (edit) (undo)
Jheide44 (Talk | contribs)

Next diff →
Line 1: Line 1:
-THESE INSTRUCTIONS ARE FOR THE VERSION 2 MODEL ONLY! This is the WRONG FILE for a V1 and V3 is not yet supported (at the time of writing this!) +[[Image:WNR2000-product.jpg | right | 200px]]
 += Initial Flash Instructions =
 + 
 +'''THESE INSTRUCTIONS ARE FOR THE VERSION 2 MODEL ONLY!''' This is the WRONG FILE for a V3 details are [http://www.dd-wrt.com/wiki/index.php/Netgear_WNR2000V3 HERE]. Also V1, V4, and V5 are listed on the [http://www.dd-wrt.com/wiki/index.php/Known_incompatible_devices incomparable devices wiki].
 + 
 + 
 + 
 += Initial Flash Instructions =
# READ the peacock announcement: http://www.dd-wrt.com/phpBB2/viewtopic.php?t=51486 # READ the peacock announcement: http://www.dd-wrt.com/phpBB2/viewtopic.php?t=51486
Line 17: Line 24:
# Repeat steps 12 and 13 and go in and configure your router. Hit save as you make your configurations before you switch to another tab, and when you are done, hit APPLY. # Repeat steps 12 and 13 and go in and configure your router. Hit save as you make your configurations before you switch to another tab, and when you are done, hit APPLY.
-'''Upgrading to later versions (2013/11/07):''' 
 += Upgrading to Later Builds =
 +==History dated 2013/11/07==
Unfortunately, '''the WNR2000v2 is limited in its flash size to 3392 KB''' (or 3,473,408 bytes). http://www.dd-wrt.com/phpBB2/viewtopic.php?t=72269&postdays=0&postorder=asc&start=165 Unfortunately, '''the WNR2000v2 is limited in its flash size to 3392 KB''' (or 3,473,408 bytes). http://www.dd-wrt.com/phpBB2/viewtopic.php?t=72269&postdays=0&postorder=asc&start=165
This limits the builds that can be used on this unit, INCLUDING the trailed builds. '''PLEASE NOTE that the last Brainslayer MINI build that will not brick this router is 18777 and the last OpenVPN-SMALL build is 18688.''' Uploading any build that is larger than 3392 KB will brick this router. This limits the builds that can be used on this unit, INCLUDING the trailed builds. '''PLEASE NOTE that the last Brainslayer MINI build that will not brick this router is 18777 and the last OpenVPN-SMALL build is 18688.''' Uploading any build that is larger than 3392 KB will brick this router.
-WNR2000v2 has a known bug with firmware 18777 and below:+==Update dated 2015/03/25==
 +It has been reported that the latest current build (26490) was able to be flashed on this device. That indicates that some of the size restrictions reported in the 2013/11/07 section above may not be accurate. See details on forum [http://www.dd-wrt.com/phpBB2/viewtopic.php?p=957525#957525 HERE], and/or flash chip size limitations as detailed in Note 4 of the [http://www.dd-wrt.com/phpBB2/viewtopic.php?t=51486 peacock thread].
 + 
 +'''File:''' [ftp://ftp.dd-wrt.com/betas/2015/03-19-2015-r26490/broadcom_K26/dd-wrt.v24-26490_NEWD-2_K2.6_mini.bin dd-wrt.v24-26490_NEWD-2_K2.6_mini.bin]<br>
 +'''MD5:''' 57a40734f3ce2cb19c579aa40e57b906
 + 
 +'''File:''' [ftp://ftp.dd-wrt.com/betas/2015/03-19-2015-r26490/broadcom_K26/dd-wrt.v24-26490_NEWD-2_K2.6_openvpn_small.bin dd-wrt.v24-26490_NEWD-2_K2.6_openvpn_small.bin]<br>
 +'''MD5:''' 3594c6623291d048c825477456a7c620
 + 
 +'''Note:''' From a 64 bit windows 7 box IE 11 did not want update firmware or apply settings on certain pages. Had more success using Firefox to upgrade/configure.
 + 
 + 
 += Known Bugs/Issues =
 + 
 +WNR2000v2 has a known bug with firmware 18777 and below (& 26490):
LAN1, LAN2, LAN3 and LAN4 port work properly under 10M/100M half/full duplex, but the LED display are incorrect: LAN1, LAN2, LAN3 and LAN4 port work properly under 10M/100M half/full duplex, but the LED display are incorrect:
LAN1 and LAN2 always amber; LAN1 and LAN2 always amber;
Line 29: Line 51:
LAN4 LED is correct, it will display amber for 10M connection and green for 100M networking. LAN4 LED is correct, it will display amber for 10M connection and green for 100M networking.
-A brick from flashing too large an image can be recovered via a pin-short to enter TFTP mode as described in this thread http://www.dd-wrt.com/phpBB2/viewtopic.php?t=81013 . Timing is very important for the short, please read the entire thread for instructions. This is not without risk!+ 
 += Bad Flash Recovery =
 + 
 +A brick from flashing too large an image can be recovered via a pin-short to enter TFTP mode as described in this thread http://www.dd-wrt.com/phpBB2/viewtopic.php?t=81013 . Timing is very important for the short, please read the entire thread for instructions. '''This is not without risk!'''
 + 
[[Category:Netgear guides]] [[Category:Netgear guides]]

Revision as of 20:59, 24 March 2015

Contents

Initial Flash Instructions

THESE INSTRUCTIONS ARE FOR THE VERSION 2 MODEL ONLY! This is the WRONG FILE for a V3 details are HERE. Also V1, V4, and V5 are listed on the incomparable devices wiki.


Initial Flash Instructions

  1. READ the peacock announcement: http://www.dd-wrt.com/phpBB2/viewtopic.php?t=51486
  2. Download this file ftp://ftp.dd-wrt.com/others/eko/BrainSlayer-V24-preSP2/2010/12-24-10-r15962/broadcom_K26/dd-wrt.v24-15962_NEWD-2_K2.6_mini-WNR2000v2.chk Note that this is a K26 file and all flashes of this router will require a K26 build!
  3. Push the reset button on the back of the router for 1 minute and release it.
  4. Attach a cable to the router and disable any wireless on your computer. Make sure the cable goes from your computer Ethernet connection to a LAN port (Not WAN port) on your router.
  5. Wait until you have a connection with the router
  6. Login to the router at 192.168.1.1
  7. At the password prompt, put admin/admin or admin/password for the username/password
  8. Go to the Router Upgrade link on the left side of the router gui and click on it
  9. Navigate to and Choose the file that you downloaded, double checking that it is the mini-WNR2000v2.chk file and not some recipe your grandma sent you or some other router file
  10. When it asks you if you want to upgrade to a different version, click on yes.
  11. Wait FIVE full earth minutes after the upgrade appears to have finished. You can watch the lights on the front if you need something to do. As long as they are changing, you need to sit quietly and wait! If you screw this up you WILL brick your router. When the green light and the blue light and the port light that you are plugged into have all stopped blinking, you should be all right as long as you have waited FIVE FULL MINUTES!
  12. Log onto the router at 192.168.1.1
  13. Change your username and password to something you will remember by TYPING in the boxes and hitting enter.
  14. Do a proper HARD RESET on your router as outlined in note 1 of the peacock announcement. THIS STEP IS IMPORTANT!
  15. Repeat steps 12 and 13 and go in and configure your router. Hit save as you make your configurations before you switch to another tab, and when you are done, hit APPLY.


Upgrading to Later Builds

History dated 2013/11/07

Unfortunately, the WNR2000v2 is limited in its flash size to 3392 KB (or 3,473,408 bytes). http://www.dd-wrt.com/phpBB2/viewtopic.php?t=72269&postdays=0&postorder=asc&start=165

This limits the builds that can be used on this unit, INCLUDING the trailed builds. PLEASE NOTE that the last Brainslayer MINI build that will not brick this router is 18777 and the last OpenVPN-SMALL build is 18688. Uploading any build that is larger than 3392 KB will brick this router.

Update dated 2015/03/25

It has been reported that the latest current build (26490) was able to be flashed on this device. That indicates that some of the size restrictions reported in the 2013/11/07 section above may not be accurate. See details on forum HERE, and/or flash chip size limitations as detailed in Note 4 of the peacock thread.

File: dd-wrt.v24-26490_NEWD-2_K2.6_mini.bin
MD5: 57a40734f3ce2cb19c579aa40e57b906

File: dd-wrt.v24-26490_NEWD-2_K2.6_openvpn_small.bin
MD5: 3594c6623291d048c825477456a7c620

Note: From a 64 bit windows 7 box IE 11 did not want update firmware or apply settings on certain pages. Had more success using Firefox to upgrade/configure.


Known Bugs/Issues

WNR2000v2 has a known bug with firmware 18777 and below (& 26490): LAN1, LAN2, LAN3 and LAN4 port work properly under 10M/100M half/full duplex, but the LED display are incorrect: LAN1 and LAN2 always amber; LAN 3 always green; LAN4 LED is correct, it will display amber for 10M connection and green for 100M networking.


Bad Flash Recovery

A brick from flashing too large an image can be recovered via a pin-short to enter TFTP mode as described in this thread http://www.dd-wrt.com/phpBB2/viewtopic.php?t=81013 . Timing is very important for the short, please read the entire thread for instructions. This is not without risk!