Netgear WNDR4500
From DD-WRT Wiki
Revision as of 06:43, 13 March 2015 (edit) JNavas (Talk | contribs) m (edit) ← Previous diff |
Revision as of 15:03, 13 March 2015 (edit) (undo) JNavas (Talk | contribs) (fix Kong link) Next diff → |
||
Line 106: | Line 106: | ||
= Build Information= | = Build Information= | ||
- | In addition to 26138, another good build for this router is '''[ | + | In addition to 26138, another good build for this router is '''[http://www.desipro.de/ddwrt-ren/K3-AC/25015-SP1/dd-wrt.v24-K3_AC.bin Kong 25015-SP1]''',<br>available only as ''DD-WRT upgrade'' (not initial flash). |
'''Forum thread for reference:''' http://dd-wrt.com/phpBB2/viewtopic.php?t=145503 | '''Forum thread for reference:''' http://dd-wrt.com/phpBB2/viewtopic.php?t=145503 | ||
[[Category:Netgear guides]] | [[Category:Netgear guides]] |
Revision as of 15:03, 13 March 2015
Contents |
Hardware Specs
CPU | Broadcom BCM4706 |
---|---|
CPU Speed | 600 MHz |
Flash ROM | 128 MB |
RAM | 128 MB |
Radios | 2.4 GHz and 5 GHz |
WLAN Support | a/b/g/n |
WLAN Max Speed | 450 mbps on 2.4Ghz and 450mbps on 5Ghz |
Antenna Location | Internal |
Switch | 4x GigE LAN + 1 GigE WAN |
USB | 2x USB 2.0 |
Versions
There are two (2) versions of the WNDR4500 which have different power adapters and take different firmware.
Be careful to flash the correct firmware for your version!
Version | WNDR4500 (v1) | WNDR4500v2 |
---|---|---|
Label on Router | WNDR4500 | WNDR4500v2 |
Power Adapter | 12VDC 5A brick type with AC cord | 12VDC 2.5A wall wart |
Netgear Support | WNDR4500 | WNDR4500v2 |
Supported from DD-WRT build | 21606 | 21656 |
Initial DD-WRT Flash | 26138 mega for WNDR4500 | 26138 mega for WNDR4500v2 |
Flashing Instructions
It's always good practice to read Peacock Thread for reference on Broadcom-based routers.
Initial DD-WRT Installation
To go from stock Netgear firmware to DD-WRT on a WNDR4500 (using router DHCP):
- Connect PC to one of router's LAN ports with no other network connections to the PC.
- Turn on router, wait for Power light to go green, then reset router:
- Hold down Reset switch with a straightened paper clip for 20 seconds.
- After releasing Reset switch, router should reboot with much flashing of lights.
- Wait for Power light to go green again.
- Clear web browser cache.
- In web browser, go to http://192.168.1.1
- Click on Advanced > Administration > Router Update.
- Select special .chk firmware file you downloaded from table above.
- Wait up to 5 minutes after router says it is done for it to reboot and Power light to go green again.
- In web browser, go to http://192.168.1.1
- Verify DD-WRT successfully installed.
- Reset router (as above), and wait for router to reboot and Power light to go green again.
- In web browser, go to http://192.168.1.1
- Login and configure DD-WRT.
DD-WRT Upgrade
Download .bin (not .chk) file of desired build from DD-WRT FTP server.
Locate correct firmware in folder netgear-wndr4500 or netgear-wndr4500v2 on main page of build.
(Do not use folders broadcom_K26 or broadcom_K3X.)
Follow Initial DD-WRT Installation procedure except using DD-WRT Administration > Firmware Upgrade.
Build Information
In addition to 26138, another good build for this router is Kong 25015-SP1,
available only as DD-WRT upgrade (not initial flash).
Forum thread for reference: http://dd-wrt.com/phpBB2/viewtopic.php?t=145503