Netgear WNDR4500

From DD-WRT Wiki

(Difference between revisions)
Jump to: navigation, search
Revision as of 19:19, 15 May 2018 (edit)
Jeremywh7 (Talk | contribs)
m (2015 Kong build link removed; two bricking reports, and it's just old anyway)
← Previous diff
Current revision (23:24, 13 March 2019) (edit) (undo)
Jeremywh7 (Talk | contribs)
m (Flashing Instructions)
 
(2 intermediate revisions not shown.)
Line 35: Line 35:
-= Versions =+==Versions==
- +
There are two (2) versions of the WNDR4500 which have different power adapters and take '''''different firmware'''''. There are two (2) versions of the WNDR4500 which have different power adapters and take '''''different firmware'''''.
Line 67: Line 66:
-= Flashing Instructions =+==Flashing Instructions==
- +Read the [[Firmware_FAQ#Where_do_I_download_firmware.3F|Firmware FAQ]] and [http://www.dd-wrt.com/phpBB2/viewtopic.php?t=51486 Peacock announcement] for reference on Broadcom-based routers.<br>
-It's always good practice to read [http://www.dd-wrt.com/phpBB2/viewtopic.php?t=51486 Peacock Thread] for reference on Broadcom-based routers.+The ddwrt (mtd3) partition is 0x5F00000 (99614720) bytes (95.0 MiB).
- +
- +
-== Initial DD-WRT Installation ==+
 +====Initial DD-WRT Installation====
To go from stock Netgear firmware to DD-WRT on a WNDR4500 (using router DHCP): To go from stock Netgear firmware to DD-WRT on a WNDR4500 (using router DHCP):
<ol> <ol>
Line 84: Line 81:
<li>In web browser, go to http://192.168.1.1</li> <li>In web browser, go to http://192.168.1.1</li>
<li>Click on Advanced > Administration > Router Update.</li> <li>Click on Advanced > Administration > Router Update.</li>
-<li>Select special '''.chk''' firmware file you downloaded from table above.</li>+<li>Select the trailed (with header) '''.chk''' firmware file you downloaded from table above.</li>
<li>Wait up to 5 minutes after router says it is done for it to reboot and Power light to go green again. <li>Wait up to 5 minutes after router says it is done for it to reboot and Power light to go green again.
<li>In web browser, go to http://192.168.1.1</li> <li>In web browser, go to http://192.168.1.1</li>
Line 92: Line 89:
<li>Login and configure DD-WRT.</ol> <li>Login and configure DD-WRT.</ol>
 +====DD-WRT Upgrade====
 +Use the '''.bin''' file (.chk is not necessary) of desired build. See forum build threads and [[Firmware_FAQ#Where_do_I_download_firmware.3F|the DD-WRT FAQ]] for more info.
 +
 +Firmware is in the root build folder: '''netgear-wndr4500''' or '''netgear-wndr4500v2''', '''not''' ''broadcom*''.
-== DD-WRT Upgrade ==+Follow Initial DD-WRT Installation procedure in the DD-WRT GUI: ''Administration'' -> ''Firmware Upgrade''.
-Download '''.bin''' (''not'' .chk) file of desired build from a link in [[Firmware_FAQ#Where_do_I_download_firmware.3F|Where do I download firmware?]].+==Serial Recovery==
 +After breaking CFE immediately after power-up, type `tftpd` then use a [[TFTP_flash|TFTP]] program to load OEM firmware.
-Locate correct firmware in folder '''netgear-wndr4500''' or '''netgear-wndr4500v2''' on ''main page of build''.+====Serial pinouts====
 +*WNDR4500v1: https://forum.dd-wrt.com/phpBB2/viewtopic.php?p=663694#663694
 +*WNDR4500v2 serial pins are on header J252 (pin1 is marked): pin2 = Rx, pin5 = Tx, pin6 = Ground
-(Do ''not'' use folders broadcom_K26 or broadcom_K3X.) 
-Follow Initial DD-WRT Installation procedure except using DD-WRT Administration > Firmware Upgrade.+==More Information==
 +WNDR4500 forum thread: [http://dd-wrt.com/phpBB2/viewtopic.php?t=145503 WNDR4500 (N900) supported?]
-=Build Information= 
-'''Forum thread for reference:''' http://dd-wrt.com/phpBB2/viewtopic.php?t=145503 
[[Category:Netgear guides]] [[Category:Netgear guides]]

Current revision

Contents

[edit] Hardware Specs

CPU Broadcom BCM4706
CPU Speed 600 MHz
Flash ROM 128 MB
RAM 128 MB
Radios 2.4 GHz and 5 GHz
WLAN Support a/b/g/n
WLAN Max Speed 450 mbps on 2.4Ghz and 450mbps on 5Ghz
Antenna Location Internal
Switch 4x GigE LAN + 1 GigE WAN
USB 2x USB 2.0


[edit] Versions

There are two (2) versions of the WNDR4500 which have different power adapters and take different firmware.

Be careful to flash the correct firmware for your version!

Version WNDR4500 (v1) WNDR4500v2
Label on Router WNDR4500 WNDR4500v2
Power Adapter 12VDC 5A brick type with AC cord 12VDC 2.5A wall wart
Netgear Support WNDR4500 WNDR4500v2
Supported from DD-WRT build 21606 21656
Initial DD-WRT Flash 26138 mega for WNDR4500 26138 mega for WNDR4500v2


[edit] Flashing Instructions

Read the Firmware FAQ and Peacock announcement for reference on Broadcom-based routers.
The ddwrt (mtd3) partition is 0x5F00000 (99614720) bytes (95.0 MiB).

[edit] Initial DD-WRT Installation

To go from stock Netgear firmware to DD-WRT on a WNDR4500 (using router DHCP):

  1. Connect PC to one of router's LAN ports with no other network connections to the PC.
  2. Turn on router, wait for Power light to go green, then reset router:
    1. Hold down Reset switch with a straightened paper clip for 20 seconds.
    2. After releasing Reset switch, router should reboot with much flashing of lights.
    3. Wait for Power light to go green again.
  3. Clear web browser cache.
  4. In web browser, go to http://192.168.1.1
  5. Click on Advanced > Administration > Router Update.
  6. Select the trailed (with header) .chk firmware file you downloaded from table above.
  7. Wait up to 5 minutes after router says it is done for it to reboot and Power light to go green again.
  8. In web browser, go to http://192.168.1.1
  9. Verify DD-WRT successfully installed.
  10. Reset router (as above), and wait for router to reboot and Power light to go green again.
  11. In web browser, go to http://192.168.1.1
  12. Login and configure DD-WRT.

[edit] DD-WRT Upgrade

Use the .bin file (.chk is not necessary) of desired build. See forum build threads and the DD-WRT FAQ for more info.

Firmware is in the root build folder: netgear-wndr4500 or netgear-wndr4500v2, not broadcom*.

Follow Initial DD-WRT Installation procedure in the DD-WRT GUI: Administration -> Firmware Upgrade.

[edit] Serial Recovery

After breaking CFE immediately after power-up, type `tftpd` then use a TFTP program to load OEM firmware.

[edit] Serial pinouts


[edit] More Information

WNDR4500 forum thread: WNDR4500 (N900) supported?