Netgear WNDR3800

From DD-WRT Wiki

(Difference between revisions)
Jump to: navigation, search
Revision as of 18:50, 27 September 2015 (edit)
KeithB (Talk | contribs)
m
← Previous diff
Revision as of 22:27, 4 April 2016 (edit) (undo)
Sploit (Talk | contribs)
(WNDR3800CH Flashing)
Next diff →
Line 85: Line 85:
<br/> <br/>
<br/> <br/>
 +
 +----
 +
 +'''<b>ATTENTION: April 4th 2016</b>
 +
 +The above information on the WNDR3800CH is Grossly Inaccurate. It must be done in the way I have outlined below. I have created an extensive guide on changing this router to American Settings and getting rid of the Charter Netgear Software. I tested extensively on Netgear Firmware up to version 1.0.0.57ch.
 +<br/>
 +<ol>'''
 +<li>http://inarea51.com/dd-wrt/builds/wndr3800ch/wndr3800chwebsite/ - Sploit's WNDR3800CH to WNDR3800 DD-WRT Guide.</li>
 +</ol>
 +<br/>
 +<br/>
 +This is my first contribution to the DD-WRT project so please be nice in the forums. lol. - Sploit
 +
= Unbricking= = Unbricking=

Revision as of 22:27, 4 April 2016

Contents

Hardware Information

CPU Atheros AR7161
CPU Speed 680 MHz
Flash ROM 16 MB
RAM 128 MB
Radio 1x 2.4GHz and 1x 5GHz
WLAN Support a/b/g/n
WLAN Max Speed 300 mbps
Antenna Location Internal
Switch 4x GigE LAN + 1 GigE WAN


Flashing Instructions

If you have an WNDR3800 with stock firmware, and the version is greater than 1.0.0.16, then you will first need to downgrade to firmware no greater than 1.0.0.16 (from here). Netgear put a check in firmware greater than 1.0.0.16 to allow only Netgear firmware from the Web GUI. It hasn't been confirmed if you can flash DD_WRT using TFTP with stock firmware greater than 1.0.0.16.

You will need these files for the flashing procedure.

If you have a North American model, you will need this for the initial flash.

ftp://ftp.dd-wrt.com/betas/2015/02-04-2015-r26138/netgear-wndr3800/wndr3800-factory_NA.img

If you have an EU or Asia model, you will need this for the initial flash.

ftp://ftp.dd-wrt.com/betas/2015/02-04-2015-r26138/netgear-wndr3800/wndr3800-factory.img

The other file located within the WNDR3800's dd-wrt dir is for upgrading to newer or older dd-wrt builds from within the dd-wrt webgui. Its naming scheme looks like so - wndr3800-webflash.bin

For going from 1.0.0.16 Netgear firmware to DD-WRT on a WNDR3800, installation goes like this:

  1. Set a static IP such as: 192.168.1.3 subnet:255.255.255.0 gateway:192.168.1.1 on the PC you will be using for the flash.
  2. Connect the PC to one of the router's LAN ports (unplug your ISP modem for the moment)
  3. Make sure to Reset to Defaults on the router prior to flashing. This can be done by performing a Hard Reset
  4. In your web browser, go to http://192.168.1.1
  5. Find the “Router Upgrade” in the menu and enter that section.
  6. Upload the .img firmware file, that you downloaded from the link above.
  7. Wait 5 minutes after the router says it is done.Make sure you clear your browsers cache between updating firmwares.
  8. Perform one more Hard Reset, then login at 192.168.1.1 and begin configuring.
  9. Enjoy dd-wrt and do not forget to donate if possible.
  • Should you want to use DHCP ip assignment, remember to un-set the static ip that you set in the above instructions.

This unit was supported as of build 18687.

For updating to a newer dd-wrt build, you should be able to use the wndr3800-webflash.bin mentioned above. Make sure to reset to defaults with a hard reset as listed above and download the appropriate dd-wrt build that you are wanting to update to. New builds can be found within the dd-wrt file server:

ftp://ftp.dd-wrt.com/betas/

WNDR3800CH Flashing

  1. Disassemble router and connect a serial port adapter to J1 connector
  2. Establish serial/terminal session at 115200,8,N to serial port
  3. Apply power to router.
  4. Interrupt U-Boot on the serial console by repeatedly pressing ENTER
  5. Reset board model ID using board_model_id_set WNDR3800
  6. Reboot router
  7. Web load Netgear v1.0.0.16 firmware
  8. Web load wndr3800-factory.img firmware




ATTENTION: April 4th 2016

The above information on the WNDR3800CH is Grossly Inaccurate. It must be done in the way I have outlined below. I have created an extensive guide on changing this router to American Settings and getting rid of the Charter Netgear Software. I tested extensively on Netgear Firmware up to version 1.0.0.57ch.

  1. http://inarea51.com/dd-wrt/builds/wndr3800ch/wndr3800chwebsite/ - Sploit's WNDR3800CH to WNDR3800 DD-WRT Guide.



This is my first contribution to the DD-WRT project so please be nice in the forums. lol. - Sploit

Unbricking

See Reinstall the firmware on a router without the setup CD recovery tool