Netgear R7000P
From DD-WRT Wiki
(Difference between revisions)
Revision as of 04:48, 20 May 2021 (edit) Kernel-panic69 (Talk | contribs) (→Hardware [http://techinfodepot.shoutwiki.com/wiki/Netgear_R7000P Specifications]) ← Previous diff |
Current revision (05:01, 20 May 2021) (edit) (undo) Kernel-panic69 (Talk | contribs) (→Installation) |
||
Line 55: | Line 55: | ||
*'''DO NOT USE THE ROUTER DATABASE!''' | *'''DO NOT USE THE ROUTER DATABASE!''' | ||
*Use builds in the ''netgear-r7000P'' directory (some are missing the ''factory-to-dd'' file) | *Use builds in the ''netgear-r7000P'' directory (some are missing the ''factory-to-dd'' file) | ||
- | *Initial flash: GUI reset then flash factory-to-dd-wrt.chk ( | + | *Initial flash: GUI reset then flash factory-to-dd-wrt.chk (r39267+)<br> ''or dd-wrt.K3_R7000P.chk <Kong> (deprecated)'' |
- | *Upgrade: netgear-'''r8000'''-webflash.bin ( | + | *Upgrade: netgear-'''r8000'''-webflash.bin (r34311-r38937); netgear-r7000p-webflash.bin (r39031+)<br> ''or dd-wrt.v24-K3_AC_ARM_R7000P.bin <Kong> (deprecated)'' |
*Reset after upgrade not usually required, but '''if you have issues, reset and manually set up''' first. | *Reset after upgrade not usually required, but '''if you have issues, reset and manually set up''' first. | ||
'''NOTE:''' The R7000P build target is the same as R8000, so older builds were named ''netgear-r8000-webflash.bin''<br> | '''NOTE:''' The R7000P build target is the same as R8000, so older builds were named ''netgear-r8000-webflash.bin''<br> | ||
[[Firmware_FAQ#Where_do_I_download_firmware.3F|Where do I download firmware?]] & forum build threads for build recommendations | [[Firmware_FAQ#Where_do_I_download_firmware.3F|Where do I download firmware?]] & forum build threads for build recommendations | ||
- | *Kong builds are deprecated | + | *'''''Kong builds are deprecated and CloneVince's firmware download resource is no longer available.''''' |
*Also see the [http://www.dd-wrt.com/phpBB2/viewtopic.php?t=51486 Peacock announcement] for historical information | *Also see the [http://www.dd-wrt.com/phpBB2/viewtopic.php?t=51486 Peacock announcement] for historical information | ||
Current revision
Contents |
[edit] Hardware Specifications
FCC ID | PY316200351 |
---|---|
Industry Canada ID | 4054A-16200351 |
Power | 12 VDC, 3.5 A |
CPU/SoC | Broadcom BCM4708C0 @ 1 GHz |
CPU Architecture | ARM Cortex A9 (2 cores) |
Flash (ROM) / RAM | 128 MiB / 256 MiB |
USB ports | 1x USB 3.0, 1x USB 2.0 |
Wireless1 chip | Broadcom BCM4365E |
Wireless2 chip | Broadcom BCM4360 |
WL1/WL2 protocols | an+ac / bgn |
MIMO config | 3x3:3 |
Antenna connectors | U.FL, RP-SMA |
Ethernet | Broadcom BCM4708C0 |
Switch | Broadcom BCM4708C0 |
LAN / WAN ports | 4 / 1 (up to 1 Gb/s) |
Serial | 4-pin header, internal, 3.3V TTL |
Supported in DD-WRT since Kong r32945M (7/31/17); r34311(netgear-r8000-webflash.bin); r39267(factory-to-ddwrt.chk)
[edit] Installation
Do not 30/30/30 reset ARM routers! Use the GUI Factory Defaults reset.
- DO NOT USE THE ROUTER DATABASE!
- Use builds in the netgear-r7000P directory (some are missing the factory-to-dd file)
- Initial flash: GUI reset then flash factory-to-dd-wrt.chk (r39267+)
or dd-wrt.K3_R7000P.chk <Kong> (deprecated) - Upgrade: netgear-r8000-webflash.bin (r34311-r38937); netgear-r7000p-webflash.bin (r39031+)
or dd-wrt.v24-K3_AC_ARM_R7000P.bin <Kong> (deprecated) - Reset after upgrade not usually required, but if you have issues, reset and manually set up first.
NOTE: The R7000P build target is the same as R8000, so older builds were named netgear-r8000-webflash.bin
Where do I download firmware? & forum build threads for build recommendations
- Kong builds are deprecated and CloneVince's firmware download resource is no longer available.
- Also see the Peacock announcement for historical information
The R7000P is misidentified as R6400v1 in builds 36816 up to 37715, so users should avoid them.
[edit] Disable LEDs
In the GUI, go to Admin->Commands and save the following as a Startup Script, then reboot:
#!/bin/sh # for i in 2 3 8 9 10; do gpio enable $i ; done for i in 11 12 13; do gpio disable $i ; done et robowr 0x0 0x18 0x1ff et robowr 0x0 0x18 0x0 et robowr 0x0 0x1a 0x0
This can alternatively be ran manually (line by line or separated by ';') from telnet/ssh/Commands Reference: dcglabs' forum post