Netgear R7000P

From DD-WRT Wiki

(Difference between revisions)
Jump to: navigation, search
Revision as of 22:59, 5 May 2020 (edit)
Jeremywh7 (Talk | contribs)
(cleanup)
← Previous diff
Revision as of 15:37, 22 June 2020 (edit) (undo)
Jeremywh7 (Talk | contribs)
m (fix forum link and add kong clonevince mirror link)
Next diff →
Line 58: Line 58:
*Upgrade: netgear-'''r8000'''-webflash.bin (BS) or dd-wrt.v24-K3_AC_ARM_R7000P.bin (Kong) *Upgrade: netgear-'''r8000'''-webflash.bin (BS) or dd-wrt.v24-K3_AC_ARM_R7000P.bin (Kong)
*Reset after upgrade not usually required, but '''if you have issues, reset and manually set up''' first. *Reset after upgrade not usually required, but '''if you have issues, reset and manually set up''' first.
-'''NOTE:''' The R7000P build target currently uses the r8000, so the webflash is named as such<br>+'''NOTE:''' The R7000P build target is the same as R8000, so older builds were named ''netgear-r8000-webflash.bin''<br>
[[Firmware_FAQ#Where_do_I_download_firmware.3F|Where do I download firmware?]] & forum build threads for build recommendations [[Firmware_FAQ#Where_do_I_download_firmware.3F|Where do I download firmware?]] & forum build threads for build recommendations
-*Kong builds are deprecated but backup website is linked here too.+*Kong builds are deprecated but a [http://ddwrt-kong.clonevince.fr/ mirror site] is linked there too.
*Also see the [http://www.dd-wrt.com/phpBB2/viewtopic.php?t=51486 Peacock announcement] for historical information *Also see the [http://www.dd-wrt.com/phpBB2/viewtopic.php?t=51486 Peacock announcement] for historical information
Line 75: Line 75:
et robowr 0x0 0x1a 0x0 et robowr 0x0 0x1a 0x0
This can alternatively be ran manually (line by line or separated by ';') from telnet/ssh/Commands This can alternatively be ran manually (line by line or separated by ';') from telnet/ssh/Commands
-Reference: [https://www.dd-wrt.com/phpBB2/viewtopic.php?p=1118576#1118576 dcglabs' forum post]+Reference: [https://forum.dd-wrt.com/phpBB2/viewtopic.php?p=1118576#1118576 dcglabs' forum post]
==Forum== ==Forum==
-[https://www.dd-wrt.com/forum/viewtopic.php?t=310669 Do not use the Tathagata build.]<br>+[https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=310669 Do not use the Tathagata build.]<br>
[[Category:Netgear guides]] [[Category:Netgear guides]]

Revision as of 15:37, 22 June 2020

Contents

Hardware Specifications

FCC ID PY316200351
Industry Canada ID 4054A-16200351
Power 12 VDC, 3.5 A
CPU/SoC Broadcom BCM4708C0 @ 1 GHz
CPU Architecture ARM Cortex A9 (2 cores)
Flash (ROM) / RAM 128 MiB / 256 MiB
USB ports 1x USB 3.0, 1x USB 2.0
Wireless1 chip Broadcom BCM4365E
Wireless2 chip Broadcom BCM4360
WL1/WL2 protocols an+ac / bgn
MIMO config 3x3:3
Antenna connectors U.FL, RP-SMA
Ethernet Broadcom BCM4708C0
Switch Broadcom BCM4708C0
LAN / WAN ports 4 / 1 (up to 1 Gb/s)
Serial 4-pin header, internal, 3.3V TTL

Supported in DD-WRT since Kong r32945M ( 7/31/17 )

Installation

Do not 30/30/30 reset ARM routers! Use the GUI Factory Defaults reset.

  • DO NOT USE THE ROUTER DATABASE!
  • Use builds in the netgear-r7000P directory (some are missing the factory-to-dd file)
  • Initial flash: GUI reset then flash factory-to-dd-wrt.chk (BS) or dd-wrt.K3_R7000P.chk (Kong)
  • Upgrade: netgear-r8000-webflash.bin (BS) or dd-wrt.v24-K3_AC_ARM_R7000P.bin (Kong)
  • Reset after upgrade not usually required, but if you have issues, reset and manually set up first.

NOTE: The R7000P build target is the same as R8000, so older builds were named netgear-r8000-webflash.bin
Where do I download firmware? & forum build threads for build recommendations

The R7000P is misidentified as R6400v1 in builds 36816 up to 37715, so users should avoid them.

Disable LEDs

In the GUI, go to Admin->Commands and save the following as a Startup Script, then reboot:

#!/bin/sh
#
for i in 2 3 8 9 10; do gpio enable $i ; done
for i in 11 12 13; do gpio disable $i ; done
et robowr 0x0 0x18 0x1ff
et robowr 0x0 0x18 0x0
et robowr 0x0 0x1a 0x0

This can alternatively be ran manually (line by line or separated by ';') from telnet/ssh/Commands Reference: dcglabs' forum post

Forum

Do not use the Tathagata build.