Netgear R7000P
From DD-WRT Wiki
(Difference between revisions)
Revision as of 02:43, 18 March 2018 (edit) Ian5142 (Talk | contribs) (Changed link.) ← Previous diff |
Revision as of 10:22, 15 November 2018 (edit) (undo) Malachi (Talk | contribs) (→Installation) Next diff → |
||
Line 60: | Line 60: | ||
'''NOTE:''' The R7000P build target currently uses the r8000, so the webflash is named as such<br> | '''NOTE:''' The R7000P build target currently uses the r8000, so the webflash is named as such<br> | ||
See the forum & [http://www.dd-wrt.com/phpBB2/viewtopic.php?t=51486 Peacock announcement] for build recommendations, also: [[Firmware_FAQ#Where_do_I_download_firmware.3F|Where do I download firmware?]] | See the forum & [http://www.dd-wrt.com/phpBB2/viewtopic.php?t=51486 Peacock announcement] for build recommendations, also: [[Firmware_FAQ#Where_do_I_download_firmware.3F|Where do I download firmware?]] | ||
+ | |||
+ | The R7000P is misidentified as an R6400v1 in builds 36816 up to 37715 see: https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=317434&postdays=0&postorder=asc&start=0 | ||
+ | So users should not use those. | ||
==Disable LEDs== | ==Disable LEDs== |
Revision as of 10:22, 15 November 2018
Contents |
Hardware Specifications
FCC ID | PY316200351 |
---|---|
Industry Canada ID | 4054A-16200351 |
Power | 12 VDC, 3.5 A |
CPU/SoC | Broadcom BCM4708C0 @ 1 GHz |
CPU Architecture | ARM Cortex A9 (2 cores) |
Flash (ROM) / RAM | 128 MiB / 256 MiB |
USB ports | 1x USB 3.0, 1x USB 2.0 |
Wireless1 chip | Broadcom BCM4365E |
Wireless2 chip | Broadcom BCM4360 |
WL1/WL2 protocols | an+ac / bgn |
MIMO config | 3x3:3 |
Antenna connectors | U.FL, RP-SMA |
Ethernet | Broadcom BCM4708C0 |
Switch | Broadcom BCM4708C0 |
LAN / WAN ports | 4 / 1 (up to 1 Gb/s) |
Serial | 4-pin header, internal, 3.3V TTL |
Supported in DD-WRT since Kong r32945M ( 7/31/17 )
Installation
Do not 30/30/30 reset ARM routers! Use the GUI Factory Defaults reset.
- BS: netgear-r7000P directory, but some are missing the factory-to-dd file
- Kong: http://www.desipro.de/ddwrt/K3-AC-Arm/
- Initial flash: GUI reset then flash factory-to-dd-wrt.chk (BS) or dd-wrt.K3_R7000P.chk (Kong)
- Upgrade: netgear-r8000-webflash.bin (BS) or dd-wrt.v24-K3_AC_ARM_R7000P.bin (Kong)
- Reset after upgrade not usually required, but if you have issues, reset and manually set up first.
NOTE: The R7000P build target currently uses the r8000, so the webflash is named as such
See the forum & Peacock announcement for build recommendations, also: Where do I download firmware?
The R7000P is misidentified as an R6400v1 in builds 36816 up to 37715 see: https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=317434&postdays=0&postorder=asc&start=0 So users should not use those.
Disable LEDs
In the GUI, go to Admin->Commands and save the following as a Startup Script, then reboot:
#!/bin/sh # for i in 2 3 8 9 10; do gpio enable $i ; done for i in 11 12 13; do gpio disable $i ; done et robowr 0x0 0x18 0x1ff et robowr 0x0 0x18 0x0 et robowr 0x0 0x1a 0x0
This can alternatively be ran manually (line by line or separated by ';') from telnet/ssh/Commands Reference: dcglabs' forum post