Netgear R7000P
From DD-WRT Wiki
(Difference between revisions)
Revision as of 15:37, 22 June 2020 (edit) Jeremywh7 (Talk | contribs) m (fix forum link and add kong clonevince mirror link) ← Previous diff |
Revision as of 04:48, 20 May 2021 (edit) (undo) Kernel-panic69 (Talk | contribs) (→Hardware [http://techinfodepot.shoutwiki.com/wiki/Netgear_R7000P Specifications]) Next diff → |
||
Line 49: | Line 49: | ||
|4-pin header, internal, 3.3V TTL | |4-pin header, internal, 3.3V TTL | ||
|}<br> | |}<br> | ||
- | Supported in DD-WRT since Kong r32945M ( 7/31/17 ) | + | Supported in DD-WRT since Kong r32945M (7/31/17); r34311(netgear-r8000-webflash.bin); r39267(factory-to-ddwrt.chk) |
==Installation== | ==Installation== |
Revision as of 04:48, 20 May 2021
Contents |
Hardware Specifications
FCC ID | PY316200351 |
---|---|
Industry Canada ID | 4054A-16200351 |
Power | 12 VDC, 3.5 A |
CPU/SoC | Broadcom BCM4708C0 @ 1 GHz |
CPU Architecture | ARM Cortex A9 (2 cores) |
Flash (ROM) / RAM | 128 MiB / 256 MiB |
USB ports | 1x USB 3.0, 1x USB 2.0 |
Wireless1 chip | Broadcom BCM4365E |
Wireless2 chip | Broadcom BCM4360 |
WL1/WL2 protocols | an+ac / bgn |
MIMO config | 3x3:3 |
Antenna connectors | U.FL, RP-SMA |
Ethernet | Broadcom BCM4708C0 |
Switch | Broadcom BCM4708C0 |
LAN / WAN ports | 4 / 1 (up to 1 Gb/s) |
Serial | 4-pin header, internal, 3.3V TTL |
Supported in DD-WRT since Kong r32945M (7/31/17); r34311(netgear-r8000-webflash.bin); r39267(factory-to-ddwrt.chk)
Installation
Do not 30/30/30 reset ARM routers! Use the GUI Factory Defaults reset.
- DO NOT USE THE ROUTER DATABASE!
- Use builds in the netgear-r7000P directory (some are missing the factory-to-dd file)
- Initial flash: GUI reset then flash factory-to-dd-wrt.chk (BS) or dd-wrt.K3_R7000P.chk (Kong)
- Upgrade: netgear-r8000-webflash.bin (BS) or dd-wrt.v24-K3_AC_ARM_R7000P.bin (Kong)
- Reset after upgrade not usually required, but if you have issues, reset and manually set up first.
NOTE: The R7000P build target is the same as R8000, so older builds were named netgear-r8000-webflash.bin
Where do I download firmware? & forum build threads for build recommendations
- Kong builds are deprecated but a mirror site is linked there too.
- Also see the Peacock announcement for historical information
The R7000P is misidentified as R6400v1 in builds 36816 up to 37715, so users should avoid them.
Disable LEDs
In the GUI, go to Admin->Commands and save the following as a Startup Script, then reboot:
#!/bin/sh # for i in 2 3 8 9 10; do gpio enable $i ; done for i in 11 12 13; do gpio disable $i ; done et robowr 0x0 0x18 0x1ff et robowr 0x0 0x18 0x0 et robowr 0x0 0x1a 0x0
This can alternatively be ran manually (line by line or separated by ';') from telnet/ssh/Commands Reference: dcglabs' forum post