Netgear R7000
From DD-WRT Wiki
Revision as of 17:35, 15 November 2017 (edit) Ian5142 (Talk | contribs) (→Performance) ← Previous diff |
Revision as of 01:02, 1 December 2019 (edit) (undo) Jeremywh7 (Talk | contribs) (→How to install) Next diff → |
||
(11 intermediate revisions not shown.) | |||
Line 1: | Line 1: | ||
- | == | + | ==R7000 Category== |
+ | Find more R7000 articles [http://www.dd-wrt.com/wiki/index.php/Category:R7000 here]<br> | ||
- | + | ==[https://wikidevi.com/wiki/Netgear_R7000 Hardware] Specifications== | |
+ | {| border="1" cellspacing="0" | ||
+ | !FCC ID | ||
+ | |PY313200233 | ||
+ | |- | ||
+ | !Industry Canada ID | ||
+ | |4054A-13200233 | ||
+ | |- | ||
+ | !Power | ||
+ | |12 VDC, 3.5 A | ||
+ | |- | ||
+ | !CPU / SoC | ||
+ | |Broadcom BCM4709A0 @1 GHz | ||
+ | |- | ||
+ | !CPU Architecture | ||
+ | |ARM Cortex A9 (2 cores) | ||
+ | |- | ||
+ | !Flash / RAM | ||
+ | |128 MiB / 256 MiB | ||
+ | |- | ||
+ | !WI1 & WI2 chip | ||
+ | |Broadcom BCM4360 | ||
+ | |- | ||
+ | !WI1/WI2 protocols | ||
+ | |an+ac / bgn | ||
+ | |- | ||
+ | !Wireless MIMO config | ||
+ | |3x3:3 | ||
+ | |- | ||
+ | !Antenna connector | ||
+ | |U.FL, RP-SMA | ||
+ | |- | ||
+ | !Ethernet & Switch | ||
+ | |Broadcom BCM4709A0 | ||
+ | |- | ||
+ | !WAN / LAN ports | ||
+ | |1 / 4 (up to 1 Gb/s) | ||
+ | |- | ||
+ | !USB ports | ||
+ | |1x USB 3.0, 1x USB 2.0 | ||
+ | |- | ||
+ | !Serial | ||
+ | |4-pin header, internal, 3.3V TTL | ||
+ | |} | ||
- | + | == Performance == | |
+ | The dual core ARM CPU is beneficial for running multiple simultaneous services on the router. | ||
- | + | SFE accelerated NAT was added to DD-WRT since build 33006 (kernel 3.10+), which [https://www.dd-wrt.com/phpBB2/viewtopic.php?p=1087382#1087382 Kong tested] at 900 Mb/s throughput (download and upload). OEM firmware uses Broadcom's proprietary CTF (Cut-Through Forwarding). | |
- | + | #Throughput with IPv4 NAT routing tops out at: | |
- | + | #*450Mb/s on latest Netgear stock firmware | |
+ | #*360Mb/s on non-SFE DD-WRT (default configuration) | ||
+ | #*425Mb/s non-SFE with a 20% overclock''' | ||
+ | #For older builds, besides overclocking, using IPv6 and doing away with NAT is another workaround. | ||
== Features == | == Features == | ||
- | + | * Linux kernel 3.10.25 | |
- | * kernel 3.10.25 | + | * Supports CPU overclocking: 1200MHz and 1400MHz possible (be very cautious) |
- | * | + | |
* OpenVPN and PPTP VPN server support | * OpenVPN and PPTP VPN server support | ||
- | * | + | * Ad blocking with Privoxy |
- | * lighttpd + php | + | * Other: lighttpd + php |
- | == | + | == How to install == |
+ | The primary Brainslayer and alternative Kong build links can be found in the [[Firmware_FAQ#Where_do_I_download_firmware.3F|Firmware FAQ]]. Both are compiled from the DD-WRT [https://svn.dd-wrt.com trac SVN], but Kong builds are deprecated (see [[#Documentation|Documentation]] for differences). | ||
- | + | ====Flash from OEM==== | |
+ | GUI reset then download and flash the .chk (trailed) file using the Netgear web interface'''*'''. | ||
+ | *''factory-to-dd-wrt.chk'' for normal builds | ||
+ | *''R7000.chk'' for Kong builds | ||
+ | ['''*'''] Newer Netgear firmware (1.0.9.64_10.2.64 and newer) prevents GUI downgrades, preventing DD-WRT installation (K3_R7000, build from 9/23/18 file has a lower version number, 1.0.5* that Netgear disallows). Until a new Kong .chk image is available, use [https://github.com/jclehner/nmrpflash/files/2898060/dd-wrt.K3_R7000_mod.zip this mod version] which provides a larger version number (thanks to @jclehner) | ||
+ | *Alternatively, use the TFTP installation method | ||
- | + | ====Upgrade from DD-WRT==== | |
+ | Use the DD-WRT [[Installation#Flashing_Your_Router_with_DD-WRT_Firmware|GUI or other installation Methods]] to flash the .bin (non-trailed) file | ||
+ | *''webflash.bin'' for normal builds | ||
+ | *''K3_AC_ARM_STD.bin'' file to flash from the GUI ''Administration'' -> ''Firmware Update'' section. | ||
- | + | == Documentation == | |
- | + | Some generic DD-WRT documentation is applicable to the R7000, but much is outdated and little refers to ARM builds. | |
- | + | ||
- | + | ||
- | + | <Kong> has written some documentation relevant to his builds [now via archive.org]: | |
- | + | * [https://web.archive.org/web/20190722040209/http://www.desipro.de/ddwrt/Readme.txt Readme & Flashing instructions] | |
- | + | * [https://web.archive.org/web/20190722040510/http://www.desipro.de/ddwrt/K3-AC-Arm/Supported%20Models Kong Supported Models] | |
+ | * [https://web.archive.org/web/20190818124044/http://tips.desipro.de/2014/02/12/wireless-starters-guide-for-first-time-dd-wrt-users/ Wireless Networking Starter Guide] | ||
+ | * [https://web.archive.org/web/20190419215908/http://tips.desipro.de/2014/03/04/using-the-integrated-webserver/ Using the Integrated Webserver] | ||
- | + | Also see: [https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=264152 Kong R7000 Configuration Best Practices or Working Solutions] | |
- | + | ==TFTP at boot for de-bricking== | |
+ | See [https://www.dd-wrt.com/phpBB2/viewtopic.php?p=1052290 here], and also [https://www.dd-wrt.com/phpBB2/viewtopic.php?p=1119529#1119529 this post] which then references [https://www.dd-wrt.com/phpBB2/viewtopic.php?t=304398 here]. | ||
- | + | ==Disable LEDs== | |
+ | [https://www.dd-wrt.com/phpBB2/viewtopic.php?p=1091000#1091000 Disable lights at boot]: go to ''Administration>Commands'', paste the code below and click ''Save Startup Script''. | ||
+ | for i in 2 3 8 9 12 13 17 18 ; do gpio enable $i ; done | ||
+ | for i in 14 15 ; do gpio disable $i ; done | ||
+ | et robowr 0x0 0x18 0x1ff | ||
+ | et robowr 0x0 0x18 0x0 | ||
+ | et robowr 0x0 0x1a 0x0 | ||
- | [[Category:Netgear guides]] | + | [[Category:Netgear guides]][[Category:R7000]] |
- | [[Category:R7000] | + |
Revision as of 01:02, 1 December 2019
Contents |
R7000 Category
Find more R7000 articles here
Hardware Specifications
FCC ID | PY313200233 |
---|---|
Industry Canada ID | 4054A-13200233 |
Power | 12 VDC, 3.5 A |
CPU / SoC | Broadcom BCM4709A0 @1 GHz |
CPU Architecture | ARM Cortex A9 (2 cores) |
Flash / RAM | 128 MiB / 256 MiB |
WI1 & WI2 chip | Broadcom BCM4360 |
WI1/WI2 protocols | an+ac / bgn |
Wireless MIMO config | 3x3:3 |
Antenna connector | U.FL, RP-SMA |
Ethernet & Switch | Broadcom BCM4709A0 |
WAN / LAN ports | 1 / 4 (up to 1 Gb/s) |
USB ports | 1x USB 3.0, 1x USB 2.0 |
Serial | 4-pin header, internal, 3.3V TTL |
Performance
The dual core ARM CPU is beneficial for running multiple simultaneous services on the router.
SFE accelerated NAT was added to DD-WRT since build 33006 (kernel 3.10+), which Kong tested at 900 Mb/s throughput (download and upload). OEM firmware uses Broadcom's proprietary CTF (Cut-Through Forwarding).
- Throughput with IPv4 NAT routing tops out at:
- 450Mb/s on latest Netgear stock firmware
- 360Mb/s on non-SFE DD-WRT (default configuration)
- 425Mb/s non-SFE with a 20% overclock
- For older builds, besides overclocking, using IPv6 and doing away with NAT is another workaround.
Features
- Linux kernel 3.10.25
- Supports CPU overclocking: 1200MHz and 1400MHz possible (be very cautious)
- OpenVPN and PPTP VPN server support
- Ad blocking with Privoxy
- Other: lighttpd + php
How to install
The primary Brainslayer and alternative Kong build links can be found in the Firmware FAQ. Both are compiled from the DD-WRT trac SVN, but Kong builds are deprecated (see Documentation for differences).
Flash from OEM
GUI reset then download and flash the .chk (trailed) file using the Netgear web interface*.
- factory-to-dd-wrt.chk for normal builds
- R7000.chk for Kong builds
[*] Newer Netgear firmware (1.0.9.64_10.2.64 and newer) prevents GUI downgrades, preventing DD-WRT installation (K3_R7000, build from 9/23/18 file has a lower version number, 1.0.5* that Netgear disallows). Until a new Kong .chk image is available, use this mod version which provides a larger version number (thanks to @jclehner)
- Alternatively, use the TFTP installation method
Upgrade from DD-WRT
Use the DD-WRT GUI or other installation Methods to flash the .bin (non-trailed) file
- webflash.bin for normal builds
- K3_AC_ARM_STD.bin file to flash from the GUI Administration -> Firmware Update section.
Documentation
Some generic DD-WRT documentation is applicable to the R7000, but much is outdated and little refers to ARM builds.
<Kong> has written some documentation relevant to his builds [now via archive.org]:
- Readme & Flashing instructions
- Kong Supported Models
- Wireless Networking Starter Guide
- Using the Integrated Webserver
Also see: Kong R7000 Configuration Best Practices or Working Solutions
TFTP at boot for de-bricking
See here, and also this post which then references here.
Disable LEDs
Disable lights at boot: go to Administration>Commands, paste the code below and click Save Startup Script.
for i in 2 3 8 9 12 13 17 18 ; do gpio enable $i ; done for i in 14 15 ; do gpio disable $i ; done et robowr 0x0 0x18 0x1ff et robowr 0x0 0x18 0x0 et robowr 0x0 0x1a 0x0