Mesh Networking with OLSR
From DD-WRT Wiki
Revision as of 10:11, 5 May 2011 (edit) Sash (Talk | contribs) (→DD-WRT > v.23 SP3) ← Previous diff |
Revision as of 10:11, 5 May 2011 (edit) (undo) Sash (Talk | contribs) (→DD-WRT > v.23 SP3) Next diff → |
||
Line 138: | Line 138: | ||
*set Operating Mode to OLSR | *set Operating Mode to OLSR | ||
*keep the basic olsr settings. they are ok for the first tests | *keep the basic olsr settings. they are ok for the first tests | ||
- | *add the correct wlan interface to olsr dependend on your wifi chip vendor and platform (e.g. on most buffalos its eth1, WRT350N its eth0, on atheros wifi based systems its athX) | + | *add the correct wlan interface to olsr dependend on your wifi chip vendor and platform (e.g. on most buffalos its eth1, WRT350N its eth0, on ralink its raX, on atheros wifi based systems its athX) |
*keep the interface settings for testing | *keep the interface settings for testing | ||
Revision as of 10:11, 5 May 2011
You are here: DD-WRT wiki mainpage / Linking Routers / Mesh Networking with OLSR
Contents |
General
What is mesh networking?
Mesh networking is used to route data, voice and instructions between nodes (typically routers). A mesh network typically consists of 2 or (many) more nodes, which exchange information about their connection-status with each other (routing updates), so that every node knows, which path he has to take to reach any other node in the mesh. When a node wants to reach another node that is not directly connected, the traffic flows over other nodes, until the final node is reached (hopping) -each node that the traffic flows through is called a hop.
Why mesh networking?
Mesh networks differ from other networks in that the component parts can all connect to each other via multiple hops. Mesh networks are self-healing: the network can still operate even when a node goes down or a connection drops. The result is a very reliable network.
Benefits of mesh networking
- self organizing
- self-healing
- low system maintenance needed
- robust due dynamic route recalculation
Disadvantages of mesh networking
- additional network traffic
The exchange of routing information (routing updates) can produce a lot of traffic-overhead, also every device that takes part of a mesh must have enough cpu/ memory to have an overview of all other routers and how to reach them. (routing table). A full routing table can get very large - as seen in BGP-Routing: a full BGP table needs 2GB of memory (300.000 active routes). There is also a danger of routing-loops that can appear because of weak routing information.
OLSR
General
OLSR is a dynamic linkstate Protocol which collects link data and dynamically calculates the best routes within the network.
Links:
http://en.wikipedia.org/wiki/OLSR http://www.olsr.org
Parameters
General:
- IpVersion
- AllowNoInt
- Pollrate
- TcRedundancy
- MprCoverage
- LinkQualityFishEye
- LinkQualityWinSize
- LinkQualityDijkstraLimit
per Interface:
- HelloInterval
- HelloValidityTime
- TcInterval
- TcValidityTime
- MidInterval
- MidValidityTime
- HnaInterval
- HnaValidityTime
- LinkQualityMult
HNA4
IcpConnect
Plugins:
Sample config file:
DebugLevel 0 IpVersion 4 AllowNoInt yes Pollrate 0.1 TcRedundancy 2 MprCoverage 7 LinkQualityFishEye 1 LinkQualityWinSize 100 LinkQualityDijkstraLimit 0 7.0 LoadPlugin "olsrd_txtinfo.so.0.1" { PlParam "Accept" "127.0.0.1" } Hna4 { } IpcConnect { MaxConnections 1 Host 127.0.0.1 Net 192.168.1.0 255.255.255.0 } LinkQualityLevel 2 UseHysteresis no Interface "eth1" { HelloInterval 5.0 HelloValidityTime 90.0 TcInterval 3.0 TcValidityTime 270.0 MidInterval 15.0 MidValidityTime 270.0 HnaInterval 15.0 HnaValidityTime 90.0 LinkQualityMult 10.100.2.5 0.5 } Interface "vlan1" { HelloInterval 5.0 HelloValidityTime 90.0 TcInterval 3.0 TcValidityTime 270.0 MidInterval 15.0 MidValidityTime 270.0 HnaInterval 15.0 HnaValidityTime 90.0 LinkQualityMult 10.100.2.5 0.5 }
Setup
DD-WRT > v.23 SP3
Try the following steps to get OLSR running: Under Wireless -> Basic Settings
- enable your prefered networking mode (use adhoc mode)
- set your wlan mode (b,g,mixed...)
- set your SSID
- set your channel
- unbridge the wlan on the wireless page
- set an ip from a different network than the router uses already
- set the network mask (e.g. to 255.255.255.0 for a /24 network)
Under Setup -> Advanced Routing
- set Operating Mode to OLSR
- keep the basic olsr settings. they are ok for the first tests
- add the correct wlan interface to olsr dependend on your wifi chip vendor and platform (e.g. on most buffalos its eth1, WRT350N its eth0, on ralink its raX, on atheros wifi based systems its athX)
- keep the interface settings for testing
Enabling NAT routing
In Gateway mode the router performs NAT, while in other modes it doesn't. When you switch the Advanced Routing Operating Mode to OLSR Router, it turns off NAT. Here is how to turn the NAT back on, assuming you followed the instructions on unbridging the wlan.
Under Administration -> Commands paste the script below into Commands and click "Save Firewall" Do this on each device.
iptables -t nat -A POSTROUTING -o $(nvram get wan_ifname) -j MASQUERADE iptables -t nat -A POSTROUTING -o $(nvram get wl0_ifname) -s $(nvram get eth1_ipaddr)/$(nvram get eth1_netmask) -d $(nvram get eth1_ipaddr)/$(nvram get eth1_netmask) -j MASQUERADE iptables -t nat -A POSTROUTING -o $(nvram get lan_ifname) -s $(nvram get lan_ipaddr)/$(nvram get lan_netmask) -d $(nvram get lan_ipaddr)/$(nvram get lan_netmask) -j MASQUERADE
External Links
--Sash 22:00, 7 June 2008 (CEST)