Linksys WRT600N
From DD-WRT Wiki
Revision as of 20:50, 5 January 2018 (edit) Ian5142 (Talk | contribs) (Updated to change Where do I download link.) ← Previous diff |
Revision as of 20:30, 18 October 2019 (edit) (undo) Jeremywh7 (Talk | contribs) (remove dead link, add partition info) Next diff → |
||
Line 12: | Line 12: | ||
*MIMO config: 2x3:2 | *MIMO config: 2x3:2 | ||
*Antenna connectors: U.FL | *Antenna connectors: U.FL | ||
+ | |||
+ | ====Partitions==== | ||
+ | CFE: | ||
+ | 0x00000000-0x00040000 : "boot" | ||
+ | 0x00040000-0x007e0000 : "linux" | ||
+ | 0x0013f430-0x007e0000 : "rootfs" | ||
+ | 0x007e0000-0x007f0000 : "factory" | ||
+ | 0x007f0000-0x00800000 : "nvram" | ||
+ | DD-WRT: | ||
+ | 0x00000000-0x00040000 : "cfe" | ||
+ | 0x00040000-0x007f0000 : "linux" | ||
+ | 0x00122000-0x00590000 : "rootfs" | ||
+ | 0x00590000-0x007f0000 : "ddwrt" | ||
+ | 0x007f0000-0x00800000 : "nvram" | ||
+ | Assuming the ''factory'' alignment is the same for v1.0 and v1.1, the size limit is 0x7F0000-0x40000 = 8060928 bytes (7872 KB).<br> | ||
==Flashing== | ==Flashing== | ||
- | '''Important:''' [http://www.dd-wrt.com/phpBB2/viewtopic.php?t=51486 | + | '''Important:''' Read the DD-WRT [[Firmware FAQ]] and [http://www.dd-wrt.com/phpBB2/viewtopic.php?t=51486 Peacock announcement] first! |
====Reset==== | ====Reset==== | ||
Line 25: | Line 40: | ||
#Flash it via the stock web interface | #Flash it via the stock web interface | ||
#Reset again after flashing | #Reset again after flashing | ||
- | + | For upgrades, use any ''/broadcom'' folder non-micro build under 7872 KB (see [[Firmware_FAQ#Where_do_I_download_firmware.3F|''Where do I download firmware?'']]) | |
- | + | *Starting with 41351, the ''broadcom_K3X_mipsel32r1'' build can be used on this device | |
- | + | *Resets are unnecessary, but reset and manually set up before reporting issues | |
- | + | *Research new build and router-specific threads before trying newer builds. | |
- | + | *If you have an issue, try clearing the web browser cache or try a different browser. | |
====Reverting to Stock Firmware==== | ====Reverting to Stock Firmware==== | ||
Line 36: | Line 51: | ||
==Known Bugs== | ==Known Bugs== | ||
====Initial Flash May Not Work / TFTP problems==== | ====Initial Flash May Not Work / TFTP problems==== | ||
- | Some users may experience "Failed to Upgrade Firmware" messages when upgrading via Linksys web interface, even when using special 600N-specific builds. Also, TFTP | + | Some users may experience "Failed to Upgrade Firmware" messages when upgrading via Linksys web interface, even when using special 600N-specific builds. Also, TFTP will not work after the router has booted, and must be initiated within 1-4 seconds after power-on. |
- | + | ||
==Resources== | ==Resources== | ||
* http://www.question-defense.com/2009/03/13/linksys-wrt-600n-wireless-router-upgraded-with-dd-wrt-firmware-issues/ | * http://www.question-defense.com/2009/03/13/linksys-wrt-600n-wireless-router-upgraded-with-dd-wrt-firmware-issues/ | ||
- | * http://www.n0dy.com/blog/2011/01/fun-with-dd-wrt/ | ||
[[Category: Linksys]] | [[Category: Linksys]] |
Revision as of 20:30, 18 October 2019
Contents |
Linksys WRT600N
Hardware Specs
WRT600N v1.0: FCC ID: Q87-WRT600NV1 WRT600N v1.1: FCC ID: Q87-WRT600NV11
- CPU: Broadcom BCM4705 (300 MHz)
- Flash: 8 MiB
- RAM: 32 MiB
- USB 2.0 port(s): 1
- Wireless chip1: Broadcom BCM4321
- Wireless chip2: Broadcom BCM2055
- MIMO config: 2x3:2
- Antenna connectors: U.FL
Partitions
CFE:
0x00000000-0x00040000 : "boot" 0x00040000-0x007e0000 : "linux" 0x0013f430-0x007e0000 : "rootfs" 0x007e0000-0x007f0000 : "factory" 0x007f0000-0x00800000 : "nvram"
DD-WRT:
0x00000000-0x00040000 : "cfe" 0x00040000-0x007f0000 : "linux" 0x00122000-0x00590000 : "rootfs" 0x00590000-0x007f0000 : "ddwrt" 0x007f0000-0x00800000 : "nvram"
Assuming the factory alignment is the same for v1.0 and v1.1, the size limit is 0x7F0000-0x40000 = 8060928 bytes (7872 KB).
Flashing
Important: Read the DD-WRT Firmware FAQ and Peacock announcement first!
Reset
As always make sure to do a proper hard reset before and after updating the firmware. This is not an optional step! Do not restore backups from a different build number or type.
Flashing DD-WRT
For initial flash, a trailed build is required which has header information required by the Linksys firmware.
- Download the 14929 WRT600N mega trailed build
- Reset to factory defaults
- Flash it via the stock web interface
- Reset again after flashing
For upgrades, use any /broadcom folder non-micro build under 7872 KB (see Where do I download firmware?)
- Starting with 41351, the broadcom_K3X_mipsel32r1 build can be used on this device
- Resets are unnecessary, but reset and manually set up before reporting issues
- Research new build and router-specific threads before trying newer builds.
- If you have an issue, try clearing the web browser cache or try a different browser.
Reverting to Stock Firmware
Simply reset and flash the stock image via TFTP or through the web interface. Make sure to reset after flashing.
Known Bugs
Initial Flash May Not Work / TFTP problems
Some users may experience "Failed to Upgrade Firmware" messages when upgrading via Linksys web interface, even when using special 600N-specific builds. Also, TFTP will not work after the router has booted, and must be initiated within 1-4 seconds after power-on.