Linksys WRT54G v3.1

From DD-WRT Wiki

(Difference between revisions)
Jump to: navigation, search
Revision as of 13:58, 22 April 2011 (edit)
Donny (Talk | contribs)
(Updated Flashing Instructions)
← Previous diff
Revision as of 13:58, 22 April 2011 (edit) (undo)
Donny (Talk | contribs)
(Updated Flashing Instructions)
Next diff →
Line 13: Line 13:
==Updated Flashing Instructions== ==Updated Flashing Instructions==
-'''Always make sure your broswer cache is cleared before doing this procedure and CAREFULLY read the peacock announcement at the start of the broadcom forum before flashing'''http://www.dd-wrt.com/phpBB2/viewtopic.php?t=51486+'''Always make sure your broswer cache is cleared before doing this procedure and CAREFULLY read the peacock announcement at the start of the broadcom forum before flashing:''' http://www.dd-wrt.com/phpBB2/viewtopic.php?t=51486
1) Restore Factory defaults from linksys webgui, download this dd-wrt build [ftp://ftp.dd-wrt.com/others/eko/BrainSlayer-V24-preSP2/2010/08-12-10-r14929/broadcom/dd-wrt.v24_mini_wrt54g.bin/broadcom/dd-wrt.v24_mini_wrt54g.bin WRT54G Trailed Build] 1) Restore Factory defaults from linksys webgui, download this dd-wrt build [ftp://ftp.dd-wrt.com/others/eko/BrainSlayer-V24-preSP2/2010/08-12-10-r14929/broadcom/dd-wrt.v24_mini_wrt54g.bin/broadcom/dd-wrt.v24_mini_wrt54g.bin WRT54G Trailed Build]

Revision as of 13:58, 22 April 2011

Linksys WRT54G v3.1

You should not have to use VINT builds on this unit. My WRT54G v3.1 has a wl0_corerev of 7 and uses NEWD builds with no problems. Below is a link in which you can reference to see if VINT is required for your unit.

http://www.dd-wrt.com/wiki/index.php/NEWD_or_VINT

In order to make somwhat use of Multiple WLANs, you must use a Vint Build, If however you do not use this feature, you can use a NEWD build on this unit just fine as stated above.

http://www.dd-wrt.com/wiki/index.php/Multiple_WLANs

Updated Flashing Instructions

Always make sure your broswer cache is cleared before doing this procedure and CAREFULLY read the peacock announcement at the start of the broadcom forum before flashing: http://www.dd-wrt.com/phpBB2/viewtopic.php?t=51486

1) Restore Factory defaults from linksys webgui, download this dd-wrt build WRT54G Trailed Build

2) Set a static IP on computer than you are flashing with, set it to 192.168.1.5

3) Access the linksys webgui at http://192.168.1.1 l:admin p:admin

4) Go to the tab Administration > Firmware Upgrade and select the WRT54G Trailed Build file that you downloaded in step 1.

5) Go ahead and flash, you need to wait 6 minutes for file to completely flash safely, do not power cycle or reset in any way!

6) Browser should refresh to the new dd-wrt webgui at 192.168.1.1 prompting you to change your user/password. Power cycle your router at this point, and then go ahead and enter a temporary user/pass after the router restarts.

7) Once in the dd-wrt webgui go to Administration > Factory Defaults and select to restore factory defaults.

8) This will hard reset your router, which will take about 2-3 minutes to complete.

9) After it is finished you can then re-access the dd-wrt webgui at 192.168.1.1, it will again want you to set a user/pass, go ahead and do so, then begin to set settings and enjoy dd-wrt.

  • Also as a side note, if you intend on using DHCP, you will want to unset your static ip.
  • If you want to run a different build flavor you are not limited to only running mini, this unit can run micro, mini, nokaid, and std flavors of dd-wrt. Do not use anything bigger than those or risk bricking your unit.
  • Newer builds can be found in the dd-wrt file server linked in the peacock announcement, as you saw when you read it before flashing!