Linksys WRT54G v3.1

From DD-WRT Wiki

(Difference between revisions)
Jump to: navigation, search
Revision as of 09:39, 13 May 2010 (edit)
Glenn (Talk | contribs)
(+Category:Linksys wiki)
← Previous diff
Current revision (08:15, 22 July 2020) (edit) (undo)
Mumblee (Talk | contribs)
m (Update of the download link in the step 1)
 
(8 intermediate revisions not shown.)
Line 1: Line 1:
-Reserved for Linksys WRT54G v3.1 only+Linksys WRT54G v3.1
-*[http://www.dd-wrt.com/dd-wrtv2/down.php?path=downloads%2Fv24%2FBroadcom%2FBroadcom+Generic%2Fvintage/ VINTage firmware]. Details [http://www.dd-wrt.com/phpBB2/viewtopic.php?t=31978&postdays=0&postorder=asc&start=0 here].+*[ftp://ftp.dd-wrt.com/others/eko/V24_TNG/svn15230 VINTage firmware]. Details [http://www.dd-wrt.com/phpBB2/viewtopic.php?t=31978&postdays=0&postorder=asc&start=0 here].
 + 
 +'''You should not have to use VINT builds on this unit. The only time you should have to use a VINT build on this unit is if you want to make use of [http://www.dd-wrt.com/wiki/index.php/Multiple_WLANs Multiple WLANs]. If you do not plan on using this feature you can use a NEWD build as linked in the flashing instructions below.'''
 + 
 +==Updated Flashing Instructions==
 + 
 +'''Always make sure your broswer cache is cleared before doing this procedure and CAREFULLY read the peacock announcement at the start of the broadcom forum before flashing:''' http://www.dd-wrt.com/phpBB2/viewtopic.php?t=51486
 + 
 +1) Restore Factory defaults from linksys webgui, download this dd-wrt build [ftp://ftp.dd-wrt.com/betas/2010/08-12-10-r14929/broadcom/dd-wrt.v24_mini_wrt54g.bin WRT54G Trailed Build]
 + 
 +2) Set a static IP on computer than you are flashing with, set it to 192.168.1.5
 + 
 +3) Access the linksys webgui at http://192.168.1.1 l:admin p:admin
 + 
 +4) Go to the tab Administration > Firmware Upgrade and select the WRT54G Trailed Build file that you downloaded in step 1.
 + 
 +5) Go ahead and flash, you need to wait 6 minutes for file to completely flash safely, do not power cycle or reset in any way!
 + 
 +6) Browser should refresh to the new dd-wrt webgui at 192.168.1.1 prompting you to change your user/password. Power cycle your router at this point, and then go ahead and enter a temporary user/pass after the router restarts.
 + 
 +7) Once in the dd-wrt webgui go to Administration > Factory Defaults and select to restore factory defaults.
 + 
 +8) This will hard reset your router, which will take about 2-3 minutes to complete.
 + 
 +9) After it is finished you can then re-access the dd-wrt webgui at 192.168.1.1, it will again want you to set a user/pass, go ahead and do so, then begin to set settings and enjoy dd-wrt.
 + 
 +* '''Also as a side note, if you intend on using DHCP, you will want to unset your static ip'''.
 + 
 +* If you want to run a different build flavor you are not limited to only running mini, this unit can run micro, mini, nokaid, and std flavors of dd-wrt. '''Do not use anything bigger than those or risk bricking your unit'''.
 + 
 +* Newer builds can be found in the dd-wrt file server linked in the peacock announcement, as you saw when you read it before flashing!
[[Category:Linksys]] [[Category:Linksys]]

Current revision

Linksys WRT54G v3.1

You should not have to use VINT builds on this unit. The only time you should have to use a VINT build on this unit is if you want to make use of Multiple WLANs. If you do not plan on using this feature you can use a NEWD build as linked in the flashing instructions below.

[edit] Updated Flashing Instructions

Always make sure your broswer cache is cleared before doing this procedure and CAREFULLY read the peacock announcement at the start of the broadcom forum before flashing: http://www.dd-wrt.com/phpBB2/viewtopic.php?t=51486

1) Restore Factory defaults from linksys webgui, download this dd-wrt build WRT54G Trailed Build

2) Set a static IP on computer than you are flashing with, set it to 192.168.1.5

3) Access the linksys webgui at http://192.168.1.1 l:admin p:admin

4) Go to the tab Administration > Firmware Upgrade and select the WRT54G Trailed Build file that you downloaded in step 1.

5) Go ahead and flash, you need to wait 6 minutes for file to completely flash safely, do not power cycle or reset in any way!

6) Browser should refresh to the new dd-wrt webgui at 192.168.1.1 prompting you to change your user/password. Power cycle your router at this point, and then go ahead and enter a temporary user/pass after the router restarts.

7) Once in the dd-wrt webgui go to Administration > Factory Defaults and select to restore factory defaults.

8) This will hard reset your router, which will take about 2-3 minutes to complete.

9) After it is finished you can then re-access the dd-wrt webgui at 192.168.1.1, it will again want you to set a user/pass, go ahead and do so, then begin to set settings and enjoy dd-wrt.

  • Also as a side note, if you intend on using DHCP, you will want to unset your static ip.
  • If you want to run a different build flavor you are not limited to only running mini, this unit can run micro, mini, nokaid, and std flavors of dd-wrt. Do not use anything bigger than those or risk bricking your unit.
  • Newer builds can be found in the dd-wrt file server linked in the peacock announcement, as you saw when you read it before flashing!