Linksys WRT54G v2.2

From DD-WRT Wiki

(Difference between revisions)
Jump to: navigation, search
Revision as of 06:40, 28 December 2009 (edit)
DHC DarkShadow (Talk | contribs)
m
← Previous diff
Revision as of 14:48, 29 January 2010 (edit) (undo)
DHC DarkShadow (Talk | contribs)
(Flashing - Correct file for flashing)
Next diff →
Line 12: Line 12:
#Leave the username blank and enter "admin" as the password #Leave the username blank and enter "admin" as the password
#Go to administration and firmware upgrade #Go to administration and firmware upgrade
-#Navigate to the folder that you are using, and select [ftp://dd-wrt.com/others/eko/BrainSlayer-V24-preSP2/09-08-09-r12874/broadcom/dd-wrt.v24_micro_generic.bin dd-wrt.v24_micro_generic.bin]+#Navigate to the folder that you are using, and select [ftp://dd-wrt.com/others/eko/BrainSlayer-V24-preSP2/10-10-09-r13064/broadcom/dd-wrt.v24_mini_wrt54g.bin dd-wrt.v24_mini_wrt54g.bin]
#Hit upgrade #Hit upgrade
#When you get a success, wait FIVE FULL minutes. #When you get a success, wait FIVE FULL minutes.

Revision as of 14:48, 29 January 2010

Contents

Inspired by Murrkf

Flashing

  1. Read the peacock announcement found here: http://www.dd-wrt.com/phpBB2/viewtopic.php?t=51486
  2. Do a HARD reset on the router according to note 1 of the peacock announcement (30/30/30)
  3. Set a static IP on your computer to 192.168.1.7. Subnet mask should be 255.255.255.0.
  4. Connect the lan cable from your computer to a LAN port of your router. Make sure your router is plugged in. Nothing should be connected to your computer or the router except the lan cable between them. Turn your firewall and any wireless computer connections OFF.
  5. Power cycle the router (uplug the power from the router for 30 seconds and then plug it back in)
  6. Open your browser to 192.168.1.1 by putting that in the browser address window of your browser. You should open the linksys webgui and NOT a page that says Management Mode. If you see management mode, power cycle the router again.
  7. Leave the username blank and enter "admin" as the password
  8. Go to administration and firmware upgrade
  9. Navigate to the folder that you are using, and select dd-wrt.v24_mini_wrt54g.bin
  10. Hit upgrade
  11. When you get a success, wait FIVE FULL minutes.
  12. If you don't get success, repeat from steps 6 up to this one. If you still don't get success, clear your browser cache. Try using a different browser as well, to navigate to 192.168.1.1.
  13. When you can access the dd-wrt webgui using a browser at 192.168.1.1, power cycle the router.
  14. When you can again access the dd-wrt webgui using a browser at 192.168.1.1, do another HARD reset on the router.
  15. At this point you can choose to put a different build on, depending on what you needs are.
  16. Reset your computer ethernet connection to auto IP and auto DNS

Reverting

  1. Read the peacock announcement found here: http://www.dd-wrt.com/phpBB2/viewtopic.php?t=51486
  2. Do a HARD reset on the router according to note 1 of the peacock announcement (30/30/30)
  3. Set a static IP on your computer to 192.168.1.7. Subnet mask should be 255.255.255.0.
  4. Connect the lan cable from your computer to a LAN port of your router. Make sure your router is plugged in. Nothing should be connected to your computer or the router except the lan cable between them. Turn your firewall and any wireless computer connections OFF.
  5. Power cycle the router (uplug the power from the router for 30 seconds and then plug it back in)
  6. Open your browser to 192.168.1.1 by putting that in the browser address window of your browser. You should open the linksys webgui and NOT a page that says Management Mode. If you see management mode, power cycle the router again.
  7. Enter your username and password
  8. Go to administration and firmware upgrade
  9. Navigate to the folder that you are using, and select WRT54G_v4.21.1_fw.bin once you've unzipped it.
  10. Hit upgrade
  11. When you get a success, wait FIVE FULL minutes.
  12. When you can again access the Linksys webgui using a browser at 192.168.1.1, do another HARD reset on the router.
  13. Reset your computer ethernet connection to auto IP and auto DNS