Linksys WRT54GS v1.0

From DD-WRT Wiki

(Difference between revisions)
Jump to: navigation, search
Revision as of 07:18, 12 February 2010 (edit)
Cpirner (Talk | contribs)
m (Other Notes)
← Previous diff
Revision as of 13:19, 21 February 2010 (edit) (undo)
4rings (Talk | contribs)
(How To Flash)
Next diff →
Line 1: Line 1:
== How To Flash == == How To Flash ==
Need confirmed instructions posted Need confirmed instructions posted
 +
 +MY INSTRUCTIONS:
 +
 +Initial Flashing:
 +Device had the original Linksys firmware on it.<br>
 +30-30-30 Hard Reset.<br>
 +Waited until lights returned to normal (longer is better).<br>
 +** There is A LOT of WAITING. Cannot emphasize that enough. Waiting is the key. **<br>
 +Logged in and flashed with dd-wrt.v24-13064_VINT_mini via the web interface.<br>
 +Waited until Upgrade Successful message and lights returned to normal (longer is better).<br>
 +30-30-30 Hard Reset.<br>
 +Waited until lights returned to normal (longer is better).<br>
 +I logged in (had to reset password) and looked around.<br>
 +30-30-30 Hard Reset.<br>
 +I wasn't done. From there, I upgraded to Mega.<br><br>
 +
 +Flashing of existing version (Upgrading from mini to Mega):<br>
 +Set my computer to a static IP of 192.168.1.8 and disabled my firewall and security.<br>
 +My computer is not wireless but if it was, I would have disabled wireless and only had the router connected to the flashing computer by an Ethernet cable.<br>
 +30-30-30 Hard Reset.<br>
 +Waited until lights returned to normal (longer is better).<br>
 +Checked for password page on re-logged in and change password.<br>
 +Flashed with dd-wrt.v24-13064_VINT_mega firmware via the web interface.<br>
 +Waited until lights returned to normal (longer is better).<br>
 +** See important2 - Failing to wait is how most people brick their routers. **<br>
 +Did a power cycle of the router (Unplugged the power cord, counted to 30 and plugged it back in).<br>
 +Waited for the lights to return to normal (cant emphasize WAITING enough).<br>
 +30-30-30 hard reset again. <br>
 +Waited until lights returned to normal (longer is better).<br>
 +Check for the password page and re-logged in to change the password.<br>
 +You should be done at this point.<br>
 +Then you can can begin configuring your router.<br>
 +Set your computer back to the way it was (TCPIP and Firewall/Security).
 +<nowiki>Insert non-formatted text here</nowiki>
== Other Notes == == Other Notes ==

Revision as of 13:19, 21 February 2010

How To Flash

Need confirmed instructions posted

MY INSTRUCTIONS:

Initial Flashing: Device had the original Linksys firmware on it.
30-30-30 Hard Reset.
Waited until lights returned to normal (longer is better).

    • There is A LOT of WAITING. Cannot emphasize that enough. Waiting is the key. **

Logged in and flashed with dd-wrt.v24-13064_VINT_mini via the web interface.
Waited until Upgrade Successful message and lights returned to normal (longer is better).
30-30-30 Hard Reset.
Waited until lights returned to normal (longer is better).
I logged in (had to reset password) and looked around.
30-30-30 Hard Reset.
I wasn't done. From there, I upgraded to Mega.

Flashing of existing version (Upgrading from mini to Mega):
Set my computer to a static IP of 192.168.1.8 and disabled my firewall and security.
My computer is not wireless but if it was, I would have disabled wireless and only had the router connected to the flashing computer by an Ethernet cable.
30-30-30 Hard Reset.
Waited until lights returned to normal (longer is better).
Checked for password page on re-logged in and change password.
Flashed with dd-wrt.v24-13064_VINT_mega firmware via the web interface.
Waited until lights returned to normal (longer is better).

    • See important2 - Failing to wait is how most people brick their routers. **

Did a power cycle of the router (Unplugged the power cord, counted to 30 and plugged it back in).
Waited for the lights to return to normal (cant emphasize WAITING enough).
30-30-30 hard reset again.
Waited until lights returned to normal (longer is better).
Check for the password page and re-logged in to change the password.
You should be done at this point.
Then you can can begin configuring your router.
Set your computer back to the way it was (TCPIP and Firewall/Security). Insert non-formatted text here

Other Notes

I installed dd-wrt.v24-13064_VINT_std.bin directly from Linksys web interface (v4.7 something) using the standard process.

  1. 30-30-30 Hard Reset (no forced password reset from orig Linksys firmware)
  2. Use firmware update page.......wait...wait...wiat
  3. reboot....wait....wait...wait
  4. 30-30-30 Hard Reset (forced password reset from new dd-wrt firmware)
  5. Configure ppoe, connect to DSL modem in bridged mode, enjoy

Getting great signal to my wireless clients and playing around with all my new features



[comment added 17/05/08 by 7E0D1450] I installed dd-wrt.v24-9433_VINT_mega.bin directly from Linksys Web Interface (Firmware version 2.07.1) without problems or issues. The procedure is:

   1. Hard Reset (press for 30 secs the reset button - IMPORTANT).
   2. Upload the firmware from Linksys Web Interface.
   3. When finished the flashing, Hard Reset (press for 30 secs the reset button - IMPORTANT).

Reference in dd-wrt forum: [1]

____________________________________________ [comment added 18/03/09 by fattrain] I installed dd-wrt.v24-9517_VINT_std.bin directly from Linksys Web Interface (Firmware version Ver.4.71.4) without problems or issues. The procedure is:

   1. Hard Reset (press for 30 secs the reset button - IMPORTANT).
   2. Upload the firmware from Linksys Web Interface.
   3. When finished the flashing, Hard Reset (press for 30 secs the reset button - IMPORTANT).

Enjoy! :-)