Linksys WRT54G2 v1.0

From DD-WRT Wiki

(Difference between revisions)
Jump to: navigation, search
Revision as of 00:59, 9 November 2008 (edit)
Doramius (Talk | contribs)
(Flash Process)
← Previous diff
Revision as of 01:02, 9 November 2008 (edit) (undo)
Doramius (Talk | contribs)
(Flash Process)
Next diff →
Line 20: Line 20:
* install Linksys tftp.exe, set your PC to static IP, 192.168.1.10. * install Linksys tftp.exe, set your PC to static IP, 192.168.1.10.
-** 1) Reset the router to defaults on the Linksys Admin page, and let it reboot+** 1) Reset the router to defaults on the Linksys Admin page, and let it reboot or manually reboot it after it is finished.
-or manually reboot it after it is finished.+** 2) Set your computer to a static IP address of 192.168.1.10 and 255.255.255.0 for a mask and plug Ethernet cable into LAN port of the G2v1 unit.
-** 2) Set your computer to a static IP address of 192.168.1.10 and 255.255.255.0 for a mask+** 3) Close all browser windows. Start the Linksys's tftp.exe utility, set IP to 192.168.1.1 and browse to the VxWorksPrep-G2V1.bin file; enter password = admin, and click Upgrade. Wait 60 seconds for it to reboot on its own. If it does not, then power cycle the router manually.
-and plug Ethernet cable into LAN port of the G2v1 unit.+** 4) DO NOT open any browser windows. Again, start Linksys's tftp.exe utility and browse to the VxWorksKiller-G2V1.bin file; enter password = admin, and click Upgrade. Wait 2 min for it to reboot on its own. If it does not, then power cycle the router manually.
-** 3) Close all browser windows. Start the Linksys's tftp.exe utility, set IP to 192.168.1.1+** 5) Tftp the DD-WRT firmware to the router, using [http://www.dd-wrt.com/dd-wrtv2/down.php?path=downloads/others/eko/WRT54G2V1+Flashing/ "dd-wrt.v24-10709_NEWD_micro.bin"] (or latest version) from the folder where you got these instructions; after successful tftp, wait 3 min for the router to finish writing new nvram defaults, etc... It should reboot on it's own at least two times, so give it the 3 min and then go to http://192.168.1.1 -If it does not reboot on its own, wait another 1 min, and then power cycle it.
-and browse to the VxWorksPrep-G2V1.bin file; enter password = admin, and click Upgrade.+** 6) When it finishes booting....do a hard reset on the unit....let it boot again, and configure.
-Wait 60 seconds for it to reboot on its own. If it does not, then power cycle the router+
-manually.+
-** 4) DO NOT open any browser windows. Again, start Linksys's tftp.exe utility and browse to+
-the VxWorksKiller-G2V1.bin file; enter password = admin, and click Upgrade. Wait+
-2 min for it to reboot on its own. If it does not, then power cycle the router+
-manually.+
-** 5) Tftp the DD-WRT firmware to the router, using [http://www.dd-wrt.com/dd-wrtv2/down.php?path=downloads/others/eko/WRT54G2V1+Flashing/ "dd-wrt.v24-10709_NEWD_micro.bin"] (or latest version) from the folder where you got these instructions; after successful tftp, wait 3 min for+
-the router to finish writing new nvram defaults, etc... It should reboot on it's own at+
-least two times, so give it the 3 min and then go to http://192.168.1.1 +
-If it does not reboot on its own, wait another 1 min, and then power cycle it.+
-** 6) When it finishes booting....do a hard reset on the unit....let it boot again,+
-and configure.+
** 7) Do not forget to set your computer back to automatically obtaining DHCP and DNS. ** 7) Do not forget to set your computer back to automatically obtaining DHCP and DNS.

Revision as of 01:02, 9 November 2008

Process developed by Eko
Wiki created by Doramius

Linksys WRT54G2 Flash Instructions

A big thanks to Eko for making this available.

Contents

Software Tools Required

- VxWorksPrep-G2V1 - VxWorksKiller-G2V1 - Linksys tftp.exe - dd-wrt.v24-10709_NEWD_micro.bin - (Always recommended to check for newer versions available)

Flash Process

  • install Linksys tftp.exe, set your PC to static IP, 192.168.1.10.
    • 1) Reset the router to defaults on the Linksys Admin page, and let it reboot or manually reboot it after it is finished.
    • 2) Set your computer to a static IP address of 192.168.1.10 and 255.255.255.0 for a mask and plug Ethernet cable into LAN port of the G2v1 unit.
    • 3) Close all browser windows. Start the Linksys's tftp.exe utility, set IP to 192.168.1.1 and browse to the VxWorksPrep-G2V1.bin file; enter password = admin, and click Upgrade. Wait 60 seconds for it to reboot on its own. If it does not, then power cycle the router manually.
    • 4) DO NOT open any browser windows. Again, start Linksys's tftp.exe utility and browse to the VxWorksKiller-G2V1.bin file; enter password = admin, and click Upgrade. Wait 2 min for it to reboot on its own. If it does not, then power cycle the router manually.
    • 5) Tftp the DD-WRT firmware to the router, using "dd-wrt.v24-10709_NEWD_micro.bin" (or latest version) from the folder where you got these instructions; after successful tftp, wait 3 min for the router to finish writing new nvram defaults, etc... It should reboot on it's own at least two times, so give it the 3 min and then go to http://192.168.1.1 -If it does not reboot on its own, wait another 1 min, and then power cycle it.
    • 6) When it finishes booting....do a hard reset on the unit....let it boot again, and configure.
    • 7) Do not forget to set your computer back to automatically obtaining DHCP and DNS.

Notes.....

It may be necessary to completely close and reopen the browser, it sometimes will return to a management screen, if you only refresh the browser after upgrading. Just close the browser and try again.


Credits

Tornado and redhawk0 for their help. Thx to Ick & gfunk911 for donating routers.