Linksys WRT400N

From DD-WRT Wiki

(Difference between revisions)
Jump to: navigation, search
Revision as of 09:38, 13 May 2010 (edit)
Glenn (Talk | contribs)
(+Category:Linksys wiki)
← Previous diff
Revision as of 21:51, 28 June 2010 (edit) (undo)
Dark Shadow (Talk | contribs)
(intitial page)
Next diff →
Line 1: Line 1:
-This page reserved for Linksys WRT400N v1.0 only+=Flashing=
-*[http://www.dd-wrt.com/phpBB2/viewtopic.php?t=66602 Progress Thread]+Files needed:
 + 
 +* (14289) [ftp://dd-wrt.com/others/eko/BrainSlayer-V24-preSP2/04-16-10-r14289/linksys_wrt400n/linksys-to-ddwrt-firmware.bin linksys-to-ddwrt-firmware.bin] - For first time flashing only
 +* (14289) [ftp://dd-wrt.com/others/eko/BrainSlayer-V24-preSP2/04-16-10-r14289/linksys_wrt400n/wrt400n-firmware.bin wrt400n-firmware.bin]
 + 
 + 
 +#Do a [http://www.dd-wrt.com/wiki/index.php/Hard_reset_or_30/30/30 Hard reset or 30/30/30] on the router
 +#Set a static IP on your computer to 192.168.1.7. Subnet mask should be 255.255.255.0.
 +#Connect the lan cable from your computer to a LAN port of your router. Make sure your router is plugged in. Nothing should be connected to your computer or the router except the lan cable between them. Turn your firewall and any wireless computer connections OFF.
 +#Power cycle the router (uplug the power from the router for 30 seconds and then plug it back in)
 +#Open your browser to 192.168.1.1 by putting that in the browser address window of your browser. You should open the linksys webgui and NOT a page that says Management Mode. If you see management mode, power cycle the router again.
 +#Leave the username blank and enter "admin" as the password
 +#Go to administration and firmware upgrade
 +#Navigate to the folder that you are using, and select [ftp://dd-wrt.com/others/eko/BrainSlayer-V24-preSP2/04-16-10-r14289/linksys_wrt400n/linksys-to-ddwrt-firmware.bin linksys-to-ddwrt-firmware.bin]
 +#Hit upgrade
 +#When you get a success, wait FIVE FULL minutes.
 +#If you don't get success, repeat from steps 6 up to this one. If you still don't get success, clear your browser cache. Try using a different browser as well, to navigate to 192.168.1.1.
 +#When you can access the dd-wrt webgui using a browser at 192.168.1.1, power cycle the router.
 +#When you can again access the dd-wrt webgui using a browser at 192.168.1.1, do another [http://www.dd-wrt.com/wiki/index.php/Hard_reset_or_30/30/30 Hard reset or 30/30/30] on the router.
 +#Go to administration and firmware upgrade
 +#Navigate to the folder that you are using, and select [ftp://dd-wrt.com/others/eko/BrainSlayer-V24-preSP2/04-16-10-r14289/linksys_wrt400n/wrt400n-firmware.bin wrt400n-firmware.bin]
 +#Hit upgrade
 +#When you get a success, wait FIVE FULL minutes.
 +#At this point you can choose to put a different build on, depending on what you needs are.
 +#Reset your computer ethernet connection to auto IP and auto DNS
 + 
 +=Reverting=
 +===TFTP Revert===
 +[[TFTP flash]] revert reported working by LOM
 +===GUI Revert===
 +Special thx to LOM, who created the file.
 + 
 +# Restore factory defaults via dd-wrt GUI.
 +# Set static IP address to 192.168.1.10
 +# Goto firmware upgrade, click browse, find the revert file [http://www.dd-wrt.com/phpBB2/download.php?id=14927 Wrt400 gui revert.bin], click upgrade.
 +# IMPORTANT: wait 5 minutes
 +# Enter 192.168.1.1 in the web browser.
 +# At the prompt, leave the username blank and enter "admin" w/o the quotes as the password.
 +# Don't forget to set your IP back to Obtain an IP address automatically.
[[Category:Linksys]] [[Category:Linksys]]

Revision as of 21:51, 28 June 2010

Contents

Flashing

Files needed:


  1. Do a Hard reset or 30/30/30 on the router
  2. Set a static IP on your computer to 192.168.1.7. Subnet mask should be 255.255.255.0.
  3. Connect the lan cable from your computer to a LAN port of your router. Make sure your router is plugged in. Nothing should be connected to your computer or the router except the lan cable between them. Turn your firewall and any wireless computer connections OFF.
  4. Power cycle the router (uplug the power from the router for 30 seconds and then plug it back in)
  5. Open your browser to 192.168.1.1 by putting that in the browser address window of your browser. You should open the linksys webgui and NOT a page that says Management Mode. If you see management mode, power cycle the router again.
  6. Leave the username blank and enter "admin" as the password
  7. Go to administration and firmware upgrade
  8. Navigate to the folder that you are using, and select linksys-to-ddwrt-firmware.bin
  9. Hit upgrade
  10. When you get a success, wait FIVE FULL minutes.
  11. If you don't get success, repeat from steps 6 up to this one. If you still don't get success, clear your browser cache. Try using a different browser as well, to navigate to 192.168.1.1.
  12. When you can access the dd-wrt webgui using a browser at 192.168.1.1, power cycle the router.
  13. When you can again access the dd-wrt webgui using a browser at 192.168.1.1, do another Hard reset or 30/30/30 on the router.
  14. Go to administration and firmware upgrade
  15. Navigate to the folder that you are using, and select wrt400n-firmware.bin
  16. Hit upgrade
  17. When you get a success, wait FIVE FULL minutes.
  18. At this point you can choose to put a different build on, depending on what you needs are.
  19. Reset your computer ethernet connection to auto IP and auto DNS

Reverting

TFTP Revert

TFTP flash revert reported working by LOM

GUI Revert

Special thx to LOM, who created the file.

  1. Restore factory defaults via dd-wrt GUI.
  2. Set static IP address to 192.168.1.10
  3. Goto firmware upgrade, click browse, find the revert file Wrt400 gui revert.bin, click upgrade.
  4. IMPORTANT: wait 5 minutes
  5. Enter 192.168.1.1 in the web browser.
  6. At the prompt, leave the username blank and enter "admin" w/o the quotes as the password.
  7. Don't forget to set your IP back to Obtain an IP address automatically.