Linksys WRT320N v1.0

From DD-WRT Wiki

Revision as of 02:50, 28 August 2010 by Buddee (Talk | contribs)
Jump to: navigation, search


WRT320N Information

Linksys WRT320N is now supported - please use only special _wrt320n.bin builds (based on kernel 2.6).

Hardware: CPU: BCM4717A 354MHz

flash: 8MB serial

ram: 32MB

radio: A + G

Antenna gain: 1st and 2nd main 1.5 dbi, 3rd antenna: 2.2 dBi Gigabit ethernet

You can reference the forum thread with 'Eko's original annoucement' with this link for more information

WARNING: Seems that Linksys wired the reset button to wrong gpio, so 30-30-30 reset doesn't work on this router (reset button works when dd-wrt runs). Also boot_wait is turned off by default (once you load dd-wrt, it is set to on).

Feedback welcome.

Installation instructions

Links to build 13973:

You will need this trailed build for the initial flash

After the initial flash with the above mini you can then use any of the other non trailed (bin's without the wrt320n name in it) K2.6 NEWD-2 Builds which can be found here...

It is advised to use build 13493 or later for WPS button hard reset button support, reference "30-30-30 reset does not work" for more info regarding how to hard reset this unit.

1) download trailed build mini with the WRT320N name in it, from the linksys firmware webgui on the wrt320N reset to defaults.

2) once reset to defaults, IP for the router should be that being said, set your pc to a static ip of

3) log back into linksys firmware webgui, go to upgrade and select the trailed 13493 k2.6 mini that you downloaded in the above link.

4) wait about 5 minutes to make sure everything took, then reaccess webgui at, by this point it should be in dd-wrt webgui asking for user/pass, set a temporary one, once you have set it log out of the browser.

5) unplug router, push and hold the WPS button on the front of the unit, while button still being held, plug the unit back in and continue holding button for 10-12 seconds, release

6) everything should then again be in defaults, access webgui once again at, it should ask you to set a user/pass, do so, then begin your setup and enjoy dd-wrt

Also if you intend on using DHCP networking, you will want to unset your static ip and make sure you have DHCP turned on within DD-WRT.

Also bbb_forever posted a very good install method as well...


Work in progress....

VLAN Support

It was previously believed that Broadcom gigabit models did not support reconfiguring VLAN's but this has been proven to be untrue. However, the VLAN GUI page does not properly configure the nvram variables associated with VLAN's and so you must configure the nvram variables manually. The Switched Ports page explains how to configure the nvram variables to get your VLAN's functional.

Known issues with the WRT320N

FLAGEL's post

Posted by FLAGEL 17-Jan-2010, last updated 05-Feb-2010

30-30-30 reset does not work

Linksys wired the reset button to the wrong GPIO, hence a 30-30-30 reset will not work.

In order to perform a hard reset on the WRT320N, you must follow these steps...

This method below only works with build 13493 or better

1) Unplug router

2) Press and hold the WPS button on the front of the unit.

3) Plug power back in with button still pressed, hold down button for 10-12 seconds.

4) Release button after 10-12 seconds. Wait 2 minutes, then access webgui at

You can also perform a hard reset by telnet or ssh by entering the following commands into the CLI.

erase nvram


The unit should now be in defaults.

Some trouble-shooting tips:

If your router is NOT getting its WAN and DNS numbers properly from the cable Internet modem, then...

- Un-plug the cable Internet modem and router, and disable your computer's LAN or Wireless adapter.

- Re-plug the cable Internet modem, wait 1 full minute, then re-plug the DD-WRT router and wait 1 full minute.

- Then enable your computer's LAN or Wireless adapter.

- This should force the DHCP protocol to get the WAN, DNS, and local IPs from your ISP provider and give them to the modem, router, and computer LAN adapter correctly.

- Then login to the DD-WRT Mini build, and go to the Status > WAN page to check the IPs numbers are displayed.

If you lose Internet access, but used to have it with the old router, then this may a possible remedy:

- Some Cable Internet providers, like Comcast, do NOT like an unknown (or foreign) MAC address device on its network, and it may (or may not) cut off Internet access within 5-30 minutes. - If that happens, then you will have to Clone the MAC Address to be the identical MAC address as either:

(a) the local computer's MAC address or (b) the previous router's WAN MAC address (yes, you might have to login to your old router to find it's WAN MAC address or look on the bottom of the router).

- Think of your previous PC or router's MAC address as the "MAC password" to use the Cable Internet system (e.g. Comcast). - Seriously, write the nasty hexadecimal MAC address down and keep it safe for any future changes to your router.

- You may NOT have realized it, but Comcast does try to get and lock down the MAC address of the first router device at the time the ISP service is first installed and set-up.

- If you want to deal with your ISP, you may have to call them to see if they can reset your MAC address to get the new MAC on your new router (instead of using the old router's MAC address). - Sometimes, it's just easier and faster to Clone the MAC Address than to deal with the ISP customer rep (who may NOT understand what you're asking about), so you decide.

Some other useful tips

Some of the above problems, such as reset button and having enough NVRAM for openVPN can be fixed by converting your WRT320N into an E2000 - -buddee

Also I have solved some of the cooling problems with these style of linksys units by adding rubber footing on the bottom of the unit for air flow, check this post for example. -buddee