Linksys EA6900

From DD-WRT Wiki

(Difference between revisions)
Jump to: navigation, search
Revision as of 15:12, 5 March 2018 (edit)
Jeremywh7 (Talk | contribs)
m ([https://wikidevi.com/wiki/Linksys_EA6900_v1.0 Hardware] Specifications)
← Previous diff
Revision as of 20:11, 19 March 2020 (edit) (undo)
Jeremywh7 (Talk | contribs)
m (Add info about the incompatible v2 Mediatek device)
Next diff →
(5 intermediate revisions not shown.)
Line 1: Line 1:
-==[https://wikidevi.com/wiki/Linksys_EA6900_v1.0 Hardware] Specifications==+'''This guide is ''only'' for the EA6900 v1.x!'''<br>
 +'''<font color=darkred>WARNING:</font> The EA6900 ''v2'' is a Mediatek MT7621AT device and not supported by DD-WRT!''' [[https://fccid.io/Q87-EA6900V2/Internal-Photos/Internal-Photo-3316462 FCC link]]
 + 
 +==Hardware [http://techinfodepot.shoutwiki.com/wiki/Linksys_EA6900_v1.0 Specifications]==
 +The [https://www.linksys.com/us/support-article?articleNum=136177 XAC1900], which comes as part of a kit with a separate DSL modem (APM105), appears to be the same device as [https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=320688 a user has flashed one to the EA6900 firmware].
{| border="1" cellspacing="0" {| border="1" cellspacing="0"
!FCC ID !FCC ID
Line 55: Line 59:
==Installation== ==Installation==
Please refer to this forum thread for the latest info: [http://www.dd-wrt.com/phpBB2/viewtopic.php?t=291230#291230 "Linksys EA 6900 Install Guide"]<br> Please refer to this forum thread for the latest info: [http://www.dd-wrt.com/phpBB2/viewtopic.php?t=291230#291230 "Linksys EA 6900 Install Guide"]<br>
 +
 +==Boot Partitions==
 +The Linksys CFE partitions flash with two linux boot partitions, switching between them after three (consecutive?) incomplete or failed boots. It also has a bug that limits NVRAM to 32KB, for which a third-party XVortex CFE (ported from an Asus RT-AC68U) is available to mitigate. The XVortex CFE only uses a single linux boot partition.
 +
 +To check the boot partitions, run this from telnet or ssh:
 + cat /proc/mtd
 +The main boot partition is 'linux' and the Linksys CFE will also have 'linux2'.
 +
 +To force switching to the other partition from current, unplug the router after ~10 seconds into boot. After the third try, it will switch the 'bootpartition' which is stored in nvram. It can also be manually altered:
 + nvram get bootpartition
 +This returns the current boot partition (0 for linux, or 1 for linux2). To change the boot e.g. to 1:
 + nvram set bootpartition=1
 +
 +The number of partial boots to switch linux partitions is controlled by maxpartialboots (default is 3):
 + nvram get maxpartialboots
 +And can be changed with 'set' as well.
 +The current number of incomplete boots is tracked with 'partialboots':
 + nvram get partialboots
 +
 +The partitions can be directly written to 'linux' (or use 'linux2' for that partition) from command prompt:
 + wget {firmware path}
 +Or enable SSH and then WinSCP (or similar) can be used to copy the file.
 + mtd unlock linux
 + mtd write {firmware file} linux
 + reboot
 +Note: if an error returns from the mtd commands, instead try 'write {firmware file} linux' (no mtd command)
 +
 +==Links==
 +DD-WRT [[Firmware_FAQ]]
 +
[[Category:Linksys]][[Category:Cisco Linksys EA Series]] [[Category:Linksys]][[Category:Cisco Linksys EA Series]]

Revision as of 20:11, 19 March 2020

This guide is only for the EA6900 v1.x!
WARNING: The EA6900 v2 is a Mediatek MT7621AT device and not supported by DD-WRT! [FCC link]

Contents

Hardware Specifications

The XAC1900, which comes as part of a kit with a separate DSL modem (APM105), appears to be the same device as a user has flashed one to the EA6900 firmware.

FCC ID Q87-EA6900
Industry Canada ID 3839A-EA6900
Power 12 VDC, 3.5 A
CPU Broadcom BCM4708A0
CPU Speed 800 MHz (2 cores)
Flash/RAM 128 MiB / 256 MiB
WI1 chip Broadcom BCM4360
WI1 protocols an+ac
WI1 MIMO config 3x3:3
WI2 chip Broadcom BCM4360
WI2 protocols bgn
WI2 MIMO config 3x3:3
Antenna connectors U.FL, RP-SMA
Switch Broadcom BCM4708A0
LAN / WAN ports 4 / 1 (up to 1 Gb/s)
USB ports 2 (USB 3.0, USB 2.0)
Serial 6-pin header, internal

Installation

Please refer to this forum thread for the latest info: "Linksys EA 6900 Install Guide"

Boot Partitions

The Linksys CFE partitions flash with two linux boot partitions, switching between them after three (consecutive?) incomplete or failed boots. It also has a bug that limits NVRAM to 32KB, for which a third-party XVortex CFE (ported from an Asus RT-AC68U) is available to mitigate. The XVortex CFE only uses a single linux boot partition.

To check the boot partitions, run this from telnet or ssh:

cat /proc/mtd

The main boot partition is 'linux' and the Linksys CFE will also have 'linux2'.

To force switching to the other partition from current, unplug the router after ~10 seconds into boot. After the third try, it will switch the 'bootpartition' which is stored in nvram. It can also be manually altered:

nvram get bootpartition	

This returns the current boot partition (0 for linux, or 1 for linux2). To change the boot e.g. to 1:

nvram set bootpartition=1	

The number of partial boots to switch linux partitions is controlled by maxpartialboots (default is 3):

nvram get maxpartialboots	

And can be changed with 'set' as well. The current number of incomplete boots is tracked with 'partialboots':

nvram get partialboots

The partitions can be directly written to 'linux' (or use 'linux2' for that partition) from command prompt:

wget {firmware path}

Or enable SSH and then WinSCP (or similar) can be used to copy the file.

mtd unlock linux
mtd write {firmware file} linux
reboot

Note: if an error returns from the mtd commands, instead try 'write {firmware file} linux' (no mtd command)

Links

DD-WRT Firmware_FAQ