Linksys E900

From DD-WRT Wiki

(Difference between revisions)
Jump to: navigation, search
Revision as of 16:36, 3 September 2012 (edit)
Buddee (Talk | contribs)
(starter for E900, will add to these new E~ series wikis later... WIP!)
← Previous diff
Revision as of 23:22, 4 September 2012 (edit) (undo)
Buddee (Talk | contribs)
(blam)
Next diff →
Line 1: Line 1:
-starter page for linksys E900, please add useful infos!+=Hardware Information=
 + 
 +{| border="1" cellspacing="0"
 +! CPU
 +| Broadcom BCM5357
 +|-
 +! CPU Speed
 +| 300 MHz
 +|-
 +! Flash ROM
 +| 8 MB
 +|-
 +! RAM
 +| 32 MB
 +|-
 +! Radio
 +| 2.4 GHz
 +|-
 +! WLAN Support
 +| b/g/n
 +|-
 +! WLAN Max Speed
 +| 300 mbps
 +|-
 +! Antenna Location
 +| Internal
 +|-
 +! MIMO Config
 +| 2 Transmit x 2 Receieve
 +|-
 +! Switch
 +| 4x 10/100 LAN + 1 10/100 WAN
 +|-
 +! USB Port
 +| None
 +|}
 + 
 + 
 += Flashing instructions for the E900 =
 + 
 +'''After using the trailed build file for the initial flash (yes the file with the router name in it) only use nv64k builds to upgrade with or you will brick your unit! '''
 + 
 +# Read the [http://www.dd-wrt.com/phpBB2/viewtopic.php?t=51486 '''Peacock Announcement'''] carefully.
 +# Disconnect all cables and wireless clients.
 +# Do a [http://www.dd-wrt.com/wiki/index.php/Hard_reset_or_30/30/30 30/30/30] reset on router
 +# Connect 1 Lan cable to pc doing the flash.
 +# Log into Linkysys Web Interface Firmware Upgrade page at 192.168.1.1 and flash the firmware [ftp://ftp.dd-wrt.com//others/eko/BrainSlayer-V24-preSP2/2012/06-08-12-r19342/broadcom_K26/dd-wrt.v24-19342_NEWD-2_K2.6_mini-e900.bin '''E900 Trailed Initial Flash Build''']
 +# Wait 5 minutes to assure flash integrity.
 +# Power cycle by unplugging the E900 for 10 seconds.
 +# Plug the E900 back in and wait about 2 minutes until it finishes booting.
 +# Do a [http://www.dd-wrt.com/wiki/index.php/Hard_reset_or_30/30/30 30/30/30] reset on router.
 +# Wait 3 minutes and log into web interface.
 +# You are done.
 + 
 +*After the initial flash - should you want to flash to a build with more features you can use a k2.6 nv64k BIG or mega build or any of the other build flavors that are of your liking for features.
 + 
 +ftp://ftp.dd-wrt.com/others/eko/BrainSlayer-V24-preSP2/2012/06-08-12-r19342/broadcom_K26/dd-wrt.v24-19342_NEWD-2_K2.6_big-nv64k.bin
 + 
 + 
 += Build information=
 + 
 +'''As noted in bold at the beginning of the flashing instructions, only use builds with nv64k in the name for upgrading - otherwise follow the initial flash instructions above if you are going from stock to dd-wrt, any other builds for upgrading an exsisting dd-wrt install without nv60k in the name will brick your router! This unit was supported with build 18946 or greater, this means you cannot use a build with a number lesser than 18946. For the safest results, use builds that are linked within this wiki as they have most likely been forum tested with ok reported results.'''
 + 
 +To find the latest builds, you can browse the DD-WRT file server and look for the broadcom_K26 folder, in there is the appropriate for your unit. '''Be aware that these are beta test builds and should be used with caution!'''
 + 
 +ftp://ftp.dd-wrt.com/others/eko/BrainSlayer-V24-preSP2

Revision as of 23:22, 4 September 2012

Hardware Information

CPU Broadcom BCM5357
CPU Speed 300 MHz
Flash ROM 8 MB
RAM 32 MB
Radio 2.4 GHz
WLAN Support b/g/n
WLAN Max Speed 300 mbps
Antenna Location Internal
MIMO Config 2 Transmit x 2 Receieve
Switch 4x 10/100 LAN + 1 10/100 WAN
USB Port None


Flashing instructions for the E900

After using the trailed build file for the initial flash (yes the file with the router name in it) only use nv64k builds to upgrade with or you will brick your unit!

  1. Read the Peacock Announcement carefully.
  2. Disconnect all cables and wireless clients.
  3. Do a 30/30/30 reset on router
  4. Connect 1 Lan cable to pc doing the flash.
  5. Log into Linkysys Web Interface Firmware Upgrade page at 192.168.1.1 and flash the firmware E900 Trailed Initial Flash Build
  6. Wait 5 minutes to assure flash integrity.
  7. Power cycle by unplugging the E900 for 10 seconds.
  8. Plug the E900 back in and wait about 2 minutes until it finishes booting.
  9. Do a 30/30/30 reset on router.
  10. Wait 3 minutes and log into web interface.
  11. You are done.
  • After the initial flash - should you want to flash to a build with more features you can use a k2.6 nv64k BIG or mega build or any of the other build flavors that are of your liking for features.

ftp://ftp.dd-wrt.com/others/eko/BrainSlayer-V24-preSP2/2012/06-08-12-r19342/broadcom_K26/dd-wrt.v24-19342_NEWD-2_K2.6_big-nv64k.bin


Build information

As noted in bold at the beginning of the flashing instructions, only use builds with nv64k in the name for upgrading - otherwise follow the initial flash instructions above if you are going from stock to dd-wrt, any other builds for upgrading an exsisting dd-wrt install without nv60k in the name will brick your router! This unit was supported with build 18946 or greater, this means you cannot use a build with a number lesser than 18946. For the safest results, use builds that are linked within this wiki as they have most likely been forum tested with ok reported results.

To find the latest builds, you can browse the DD-WRT file server and look for the broadcom_K26 folder, in there is the appropriate for your unit. Be aware that these are beta test builds and should be used with caution!

ftp://ftp.dd-wrt.com/others/eko/BrainSlayer-V24-preSP2