Linksys E800
From DD-WRT Wiki
(Difference between revisions)
Revision as of 19:52, 28 June 2022 (edit) Kernel-panic69 (Talk | contribs) (New page: =[https://wikidevi.wi-cat.ru/Linksys_E800 Hardware Information]= {| border="1" cellspacing="0" ! CPU | Broadcom [https://wikidevi.wi-cat.ru/Broadcom#.28a.29bgn_3 BCM5357] |- ! CPU Speed |...) ← Previous diff |
Current revision (19:54, 28 June 2022) (edit) (undo) Kernel-panic69 (Talk | contribs) (→[https://wikidevi.wi-cat.ru/Linksys_E800 Hardware Information] - (correct MIMO config)) |
||
Line 24: | Line 24: | ||
|- | |- | ||
! MIMO Config | ! MIMO Config | ||
- | | | + | | 1 Transmit x 1 Receive |
|- | |- | ||
! Switch Ports LAN/WAN | ! Switch Ports LAN/WAN |
Current revision
Contents |
[edit] Hardware Information
CPU | Broadcom BCM5357 |
---|---|
CPU Speed | 300 MHz |
RAM/Flash (ROM) | 32 MB / 8 MB [1] |
Radio | 2.4 GHz |
WLAN Support | b/g/n |
WLAN Max Speed | 300 Mb/s |
Antenna Location | Internal |
MIMO Config | 1 Transmit x 1 Receive |
Switch Ports LAN/WAN | 4 / 1 (both 10/100 Mb/s) |
USB Port | None |
[edit] Build Information
NOTE: [1] The E800 has 64 KB more than most 8MB routers: 8060928 bytes (7872 KB). Do not flash larger builds!
- Never use a build older than 21676, as E800 support was added then.
CAUTION: To avoid bricking, only use a trailed build (the file with the router name) for initial flash, and nv64k (or trailed) builds to upgrade!
- Some Linksys E-Series units use nv60k builds, the E800 uses nv64k builds.
- See: Where do I download firmware? for build links, and read the new build thread prior to flash.
[edit] Flashing instructions for the E800
- Read the Build Information and Peacock Announcement.
- Disconnect all cables and wireless clients.
- Hard reset (or GUI reset) the router
- Connect via LAN cable to the PC doing the flash.
- Log into Linksys Web Interface "Firmware Upgrade" page (default: 192.168.1.1)
- Flash a trailed build (with 'E800' in the file name) from the broadcom_K26 folder.
- 21676_NEWD-2_K2.6_mini-e900.bin is a known good initial flash build
- Wait 5 minutes to assure flash integrity.
- Power cycle by unplugging the E800 for 10 seconds.
- Plug the E800 back in and wait about 2 minutes until it finishes booting.
- Reset again. Another power cycle may be required after this, as noted by some forum users.
- Wait 3 minutes and log into web interface.
After initial flash, a K26 big, mega, or K3X build can be flashed for more features (newer or same version).
- Only upgrade with nv64k or trailed builds.
[edit] LAN ports not working
This can affect several Linksys E-series routers.
- Go to Setup->VLANs
- Untick the boxes 1,2,3,4 in the VLAN 0 row
- Tick the boxes 1,2,3,4 in the VLAN 1 row
- Also set Assigned to Bridge LAN (in the VLAN 1 row)
- Apply Settings
[edit] Reverting to stock firmware
Download the stock firmware image from the manufacturer's website, reset the router back to defaults using a 30-30-30 hard reset, then flash the stock image from within the dd-wrt webgui. After 5 minutes it should finish, you will then need to do another 30-30-30 reset and then access the stock webgui @ 192.168.1.1
[edit] Useful Links
- Forum thread regarding the E800 New Linksys/Cisco E800 N150 Router 5/5/13 TEST BIN PAGE 1
- Mini build to Mega build question - Linksys E800