Linksys E3200
From DD-WRT Wiki
Revision as of 16:53, 30 December 2011 (edit) DasShrubber (Talk | contribs) (→Hardware Specifications) ← Previous diff |
Revision as of 14:42, 22 January 2012 (edit) (undo) Voducngh (Talk | contribs) m (Add information for firmware installation) Next diff → |
||
Line 41: | Line 41: | ||
'''2.4GHz output power per TX chain''' | '''2.4GHz output power per TX chain''' | ||
- | |||
802.11b: Max. 20.5dBm @ All rates | 802.11b: Max. 20.5dBm @ All rates | ||
- | |||
802.11g: Max. 20.5dBm @ Low rates | 802.11g: Max. 20.5dBm @ Low rates | ||
- | |||
Max. 19.5dBm @ High rates | Max. 19.5dBm @ High rates | ||
- | |||
Wireless-N 20MHz: Max. 20.5dBm @ Low rates | Wireless-N 20MHz: Max. 20.5dBm @ Low rates | ||
- | |||
Max. 18.5dBm @ High rates | Max. 18.5dBm @ High rates | ||
- | |||
Wireless-N 40MHz: Max. 17.0dBm @ All rates | Wireless-N 40MHz: Max. 17.0dBm @ All rates | ||
'''5GHz output power per TX chain''' | '''5GHz output power per TX chain''' | ||
- | |||
UNII-1 (5150-5250GHz) | UNII-1 (5150-5250GHz) | ||
- | |||
802.11a: Max. 14.0dBm @ All rates | 802.11a: Max. 14.0dBm @ All rates | ||
- | |||
Wireless-N 20MHz: Max. 11.5dBm @ All rates | Wireless-N 20MHz: Max. 11.5dBm @ All rates | ||
- | |||
Wireless-N 40MHz: Max. 12.0dBm @ All rates | Wireless-N 40MHz: Max. 12.0dBm @ All rates | ||
- | |||
UNII-3 (5725-5850GHz) | UNII-3 (5725-5850GHz) | ||
- | |||
802.11a: Max. 17.5dBm @ High rates | 802.11a: Max. 17.5dBm @ High rates | ||
- | |||
802.11a: Max. 20.0dBm @ Low rates | 802.11a: Max. 20.0dBm @ Low rates | ||
- | |||
Wireless-N 20MHz: Max. 17.5dBm @ High rates | Wireless-N 20MHz: Max. 17.5dBm @ High rates | ||
- | |||
Wireless-N 20MHz: Max. 20.0dBm @ Low rates | Wireless-N 20MHz: Max. 20.0dBm @ Low rates | ||
- | |||
Wireless-N 40MHz: Max. 17.5dBm @ High rates | Wireless-N 40MHz: Max. 17.5dBm @ High rates | ||
- | |||
Wireless-N 40MHz: Max. 21.0dBm @ Low rates | Wireless-N 40MHz: Max. 21.0dBm @ Low rates | ||
- | |||
Internal PIFA antennas are rated at 3dBi | Internal PIFA antennas are rated at 3dBi | ||
= Flashing instructions for the E3200 = | = Flashing instructions for the E3200 = | ||
+ | '''DON'T BRICK YOUR ROUTER! AFTER FLASHING WITH THE TRAILED BUILD, IF YOU THEN FLASH A BUILD THAT DOESN'T HAVE e2k-e3k in the NAME OF THE BUILD YOU ARE FLASHING YOU *WILL* BRICK YOUR e3200 ROUTER. ALSO reference this post regarding the newer NV60K.BINS FOR ALL E~ Series linksys http://www.dd-wrt.com/phpBB2/viewtopic.php?p=569485&highlight=#569485 ''' | ||
+ | |||
+ | # READ the Peacock Announcement Carefully! http://www.dd-wrt.com/phpBB2/viewtopic.php?t=51486 | ||
+ | # Disconnect all cables and wireless clients. | ||
+ | # Do a [http://www.dd-wrt.com/wiki/index.php/Hard_reset_or_30/30/30 30/30/30] reset on router | ||
+ | # Connect 1 Lan cable to pc doing the flash. | ||
+ | # Log into Web Interface and flash the firmware [ftp://ftp.dd-wrt.com/others/eko/BrainSlayer-V24-preSP2/2010/08-12-10-r14929/broadcom_K26/dd-wrt.v24-14929_NEWD-2_K2.6_std_usb_ftp-e3200.bin '''14929 E3200 Trailed Initial Flash Build'''] | ||
+ | # Wait 10 minutes until WLAN (wireless) light turns on. | ||
+ | # Power cycle by unplugging E3200 for 30 secs. | ||
+ | # Plug E3200 back in and wait about 5 minutes until it finishes booting. | ||
+ | # Do a [http://www.dd-wrt.com/wiki/index.php/Hard_reset_or_30/30/30 30/30/30] reset on router. | ||
+ | # Wait 3 minutes and log into web interface. |
Revision as of 14:42, 22 January 2012
Hardware Specifications
CPU | Broadcom BCM5357 | 500 MHz |
---|---|---|
Flash ROM | Winbond 25Q128BUFG | 16 MB |
RAM | EtronTech EM6AB160TSC-5G 32M x 16 bit | 64 MB |
Radios | 2.4 GHz, 5 GHz | |
WLAN Support | a/b/g/n | |
WLAN Max Speed | 300 mbps | |
Antenna Location | Internal | |
Switch | BCM53125SKMMLG | 4x GigE + 1 WAN |
USB | 1x USB 2.0 |
You can use some of these figures to come up with what Tx power rating would be best for you. As factory lists it a max of 20dBm then a setting of 100mW could be used as 20dBm = 100mW 17dBm = 50mW and so on.
2.4GHz output power per TX chain 802.11b: Max. 20.5dBm @ All rates 802.11g: Max. 20.5dBm @ Low rates Max. 19.5dBm @ High rates Wireless-N 20MHz: Max. 20.5dBm @ Low rates Max. 18.5dBm @ High rates Wireless-N 40MHz: Max. 17.0dBm @ All rates
5GHz output power per TX chain UNII-1 (5150-5250GHz) 802.11a: Max. 14.0dBm @ All rates Wireless-N 20MHz: Max. 11.5dBm @ All rates Wireless-N 40MHz: Max. 12.0dBm @ All rates UNII-3 (5725-5850GHz) 802.11a: Max. 17.5dBm @ High rates 802.11a: Max. 20.0dBm @ Low rates Wireless-N 20MHz: Max. 17.5dBm @ High rates Wireless-N 20MHz: Max. 20.0dBm @ Low rates Wireless-N 40MHz: Max. 17.5dBm @ High rates Wireless-N 40MHz: Max. 21.0dBm @ Low rates Internal PIFA antennas are rated at 3dBi
Flashing instructions for the E3200
DON'T BRICK YOUR ROUTER! AFTER FLASHING WITH THE TRAILED BUILD, IF YOU THEN FLASH A BUILD THAT DOESN'T HAVE e2k-e3k in the NAME OF THE BUILD YOU ARE FLASHING YOU *WILL* BRICK YOUR e3200 ROUTER. ALSO reference this post regarding the newer NV60K.BINS FOR ALL E~ Series linksys http://www.dd-wrt.com/phpBB2/viewtopic.php?p=569485&highlight=#569485
- READ the Peacock Announcement Carefully! http://www.dd-wrt.com/phpBB2/viewtopic.php?t=51486
- Disconnect all cables and wireless clients.
- Do a 30/30/30 reset on router
- Connect 1 Lan cable to pc doing the flash.
- Log into Web Interface and flash the firmware 14929 E3200 Trailed Initial Flash Build
- Wait 10 minutes until WLAN (wireless) light turns on.
- Power cycle by unplugging E3200 for 30 secs.
- Plug E3200 back in and wait about 5 minutes until it finishes booting.
- Do a 30/30/30 reset on router.
- Wait 3 minutes and log into web interface.