Linksys E2500

From DD-WRT Wiki

(Difference between revisions)
Jump to: navigation, search
Revision as of 02:57, 10 July 2012 (edit)
Buddee (Talk | contribs)
m (Flashing instructions for the E2500 - tighten up links)
← Previous diff
Revision as of 00:50, 25 August 2012 (edit) (undo)
Buddee (Talk | contribs)
m (Flashing instructions for the E2500)
Next diff →
Line 44: Line 44:
# Connect 1 Lan cable to pc doing the flash. # Connect 1 Lan cable to pc doing the flash.
# Log into Linkysys Web Interface Firmware Upgrade page at 192.168.1.1 and flash the firmware [ftp://ftp.dd-wrt.com//others/eko/BrainSlayer-V24-preSP2/2012/06-08-12-r19342/broadcom_K26/dd-wrt.v24-19342_NEWD-2_K2.6_mini-e2500.bin '''E2500 Trailed Initial Flash Build'''] # Log into Linkysys Web Interface Firmware Upgrade page at 192.168.1.1 and flash the firmware [ftp://ftp.dd-wrt.com//others/eko/BrainSlayer-V24-preSP2/2012/06-08-12-r19342/broadcom_K26/dd-wrt.v24-19342_NEWD-2_K2.6_mini-e2500.bin '''E2500 Trailed Initial Flash Build''']
-# Wait 10 minutes until WLAN (wireless) light turns on.+# Wait 10 minutes to assure flash integrity.
# Power cycle by unplugging E2500 for 10 seconds. # Power cycle by unplugging E2500 for 10 seconds.
# Plug E2500 back in and wait about 3 minutes until it finishes booting. # Plug E2500 back in and wait about 3 minutes until it finishes booting.

Revision as of 00:50, 25 August 2012

Hardware Information

Image:e25002.jpg

CPU Broadcom BCM5358U
CPU Speed 300 MHz
Flash ROM 8 MB
RAM 64 MB
Radio 2x 2.4 GHz or 5 GHz
WLAN Support a/b/g/n
WLAN Max Speed 300 mbps
Antenna Location Internal
Switch 4x 10/100 LAN + 1 10/100 WAN


Flashing instructions for the E2500

After using the trailed build file for the initial flash (yes the file with the router name in it) only use nv60k builds to upgrade with or you will brick your unit!

  1. Read the Peacock Announcement carefully.
  2. Disconnect all cables and wireless clients.
  3. Do a 30/30/30 reset on router
  4. Connect 1 Lan cable to pc doing the flash.
  5. Log into Linkysys Web Interface Firmware Upgrade page at 192.168.1.1 and flash the firmware E2500 Trailed Initial Flash Build
  6. Wait 10 minutes to assure flash integrity.
  7. Power cycle by unplugging E2500 for 10 seconds.
  8. Plug E2500 back in and wait about 3 minutes until it finishes booting.
  9. Do a 30/30/30 reset on router.
  10. Wait 3 minutes and log into web interface.
  11. You are done.
  • After the initial flash - should you want to flash to a build with more features you can use a k2.6 nv60k BIG or mega build or any of the other build flavors that are of your liking for features.

ftp://ftp.dd-wrt.com/others/eko/BrainSlayer-V24-preSP2/2012/06-08-12-r19342/broadcom_K26/dd-wrt.v24-19342_NEWD-2_K2.6_big-nv60k.bin

Build information

As noted in bold at the beginning of the flashing instructions, only use builds with nv60k in the name for upgrading - otherwise follow the initial flash instructions above if you are going from stock to dd-wrt, any other builds without nv60k in the name will brick your router! This unit was supported with build 18946 or greater, this means you cannot use a build with a number lesser than 18946, also avoid the test builds within the E2500 forum thread as they are known to cause a reboot loop.

To find the latest builds, you can browse the DD-WRT file server and look for the broadcom_K26 folder, in there is the appropriate for your unit. Be aware that these are beta test builds and should be used with caution!

ftp://ftp.dd-wrt.com/others/eko/BrainSlayer-V24-preSP2