Linksys E2000

From DD-WRT Wiki

(Difference between revisions)
Jump to: navigation, search
Revision as of 19:14, 6 November 2017 (edit)
Jeremywh7 (Talk | contribs)
m (E2000 Flashing Instructions)
← Previous diff
Revision as of 19:15, 6 November 2017 (edit) (undo)
Jeremywh7 (Talk | contribs)
m (Experimental Builds)
Next diff →
Line 58: Line 58:
==Experimental Builds== ==Experimental Builds==
* Recommended builds are in the Peacock announcement * Recommended builds are in the Peacock announcement
-* Research "New Builds" threads or those specific to the E2000 before flashing new firmware or '''YOU MAY BRICK YOUR ROUTER'''+* Research "New Builds" threads or those specific to the E2000 before flashing new firmware
* K3X builds (kernel 3.x) are available for the E2000 as well. * K3X builds (kernel 3.x) are available for the E2000 as well.
** K3X builds newer than 33006 have SFE accelerated NAT ** K3X builds newer than 33006 have SFE accelerated NAT
-* '''Newer is not always better!'''+* '''Newer is not always better! YOU MAY BRICK YOUR ROUTER'''
Tmittelstaedt confirmed (10/14/2017) that [https://download1.dd-wrt.com/dd-wrtv2/downloads/betas/2017/10-10-2017-r33492/broadcom_K26/dd-wrt.v24-33492_NEWD-2_K2.6_mega-nv60k.bin build 33492] loads on the E2000 and wireless works. Tmittelstaedt confirmed (10/14/2017) that [https://download1.dd-wrt.com/dd-wrtv2/downloads/betas/2017/10-10-2017-r33492/broadcom_K26/dd-wrt.v24-33492_NEWD-2_K2.6_mega-nv60k.bin build 33492] loads on the E2000 and wireless works.

Revision as of 19:15, 6 November 2017

Contents

E2000 Hardware Specs

Image:e2k.jpg


CPU Broadcom BCM4717A
CPU Speed 354 MHz
Flash ROM 8 MB
RAM 32 MB
Radio 1x 2.4 GHz or 5 GHz selectable
WLAN Support a/b/g/n
WLAN Max Speed 300 mbps
Antenna Location 3x Internal
Switch 4x GigE + 1 Gbit WAN

E2000 Flashing Instructions

DON'T BRICK YOUR ROUTER! Only use the trailed builds (with 'e2000' in the file name) for initial flashing or it may result in a bricked unit! Also reference this post regarding the newer nv60k.bin files which replace the e2k-e3k.bin files.

Initial Flash from Linksys firmware:

  1. READ the Peacock Announcement carefully!
  2. Disconnect all cables and wireless clients.
  3. Do a hard reset.
  4. Connect a LAN cable to the PC doing the flash.
  5. Log into Linksys Firmware Upgrade page at 192.168.1.1 and flash the 14929 E2000 Trailed Build
  6. Wait 10 minutes until WLAN (wireless) light turns on.
  7. Power cycle by unplugging E2000 for 30 secs.
  8. Plug back in and wait about 5 minutes until it finishes booting.
  9. Do a hard reset.
  10. Wait 3 minutes and log into web interface.
  11. You are done. There is no requirement to flash any other build.

Flash when already running DD-WRT firmware:

Experimental Builds

  • Recommended builds are in the Peacock announcement
  • Research "New Builds" threads or those specific to the E2000 before flashing new firmware
  • K3X builds (kernel 3.x) are available for the E2000 as well.
    • K3X builds newer than 33006 have SFE accelerated NAT
  • Newer is not always better! YOU MAY BRICK YOUR ROUTER

Tmittelstaedt confirmed (10/14/2017) that build 33492 loads on the E2000 and wireless works.

Experimental Build Specific Information

List of builds tested by Bturnbough:



ContributorBuild DateKernelBuild NumberBuild TypeNotes
Brainslayer8/12/102.614929std-usb-ftp1) Router database recommended build.
2) No known issues
3) Can be used as initial flash file from the factory default.
Brainslayer12/24/102.615962std-usb-nas1) No known issues -- Highly recommended by MSGBoard Moderators
2) Can be used as initial flash file from the factory default.
Brainslayer3/25/132.621061mini1) Can be used as initial flash file from the factory default.
Brainslayer3/25/132.621061mega1) Can NOT be used as initial flash file from the factory default.
2) SSH Broken
Brainslayer5/27/132.621676mega1) Can NOT be used as initial flash file from the factory default.
2) SSH Broken
Brainslayer4/18/142.623919mini1) Can be used as initial flash file from the factory default.
Brainslayer4/18/142.623919mega1) Can NOT be used as initial flash file from the factory default.
2) Wireless Broken.
Brainslayer5/23/142.624118mega1) Can NOT be used as initial flash file from the factory default.
2) Wireless Broken.
Brainslayer5/27/142.624160mega1) Can NOT be used as initial flash file from the factory default.
2) Wireless Broken.
3) SSH Broken.
Brainslayer6/23/143.024461mega
Brainslayer10/23/142.625143-testingmega1) Can NOT be used as initial flash file from the factory default.
2) Wont flash -- Too big?
Brainslayer10/29/142.625203mini1) Can be used as initial flash file from the factory default.
2) Wireless broken.
Brainslayer10/29/143.025203mega1) Can be used as initial flash file from the factory default.
2) SSH broken.
3) HTTPS broken.
4) Wireless works, AFAICT.
5) Telnet works.
6) HTTP works.

DD-WRT E2000 Build information

Recommended Build

The recommended version is 14929 as of 1/3/2011. (Reference Thread)


The latest builds for this unit can be currently found in the FTP. Support was added in 14826 and on.

Eko K2.6 NEWD-2 Builds

ftp://ftp.dd-wrt.com/others/eko/V24-K26/

Brainslayer added E2000 Support from 14929 and on and builds are to be found in the broadcom_K26 folder of his build branch.

ftp://ftp.dd-wrt.com/others/eko/BrainSlayer-V24-preSP2/

Also it has been asked about the builds with e2k-e3k name in them, these builds are for if you already have those units flashed with dd-wrt AND ARE THE ONLY ONES YOU CAN USE TO FLASH THIS ROUTER IF YOU HAVE DD-WRT ON IT. You MUST use one of those e2k-e3k named builds to upgrade, but the initial flash should always be done with the trailed build (build with the unit only name in it) linked above. ALSO reference this post regarding the newer NV60K.BINS FOR ALL E~ Series linksys http://www.dd-wrt.com/phpBB2/viewtopic.php?p=569485&highlight=#569485

Build 21676 Mega works on this router (tested 3/2/2014)

Per this post from Sept 5, 2016 at [1] version 25974 found at [2] works well and K2.6 builds after that have trouble with VAPs. Do initial flash with 21061 K2.6_mini-e2000.bin.

Notes

  • The E-series Linksys units have poor ventilation, so cooling can be very important to its performance. 'buddee' has a nice and easy mod that will improve air flow for under the unit.
  • After further study, the E2000 was found to have an EIRP rating of 17dBm, so it is best to run these units at a TxPower of 50mW (50mW = 17dBm) instead of the dd-wrt default 71mW. This can be adjusted in the webgui (Wireless > Advanced Settings), which should help the unit run cooler and have less Tx/Rx errors.
  • If you experience wireless disconnects, try the following settings:
Wireless > Channel > Ch 161 (5GhZ)
Wireless > Channel > Ch 9     (2.4GhZ)
Wireless > Security > WPA2 Personal - AES
Wireless > Advanced Wireless Settings > Beacon Interval: 75
Wireless > Advanced Wireless Settings > Fragmentation Threshold: 2306
Wireless > Advanced Wireless Settings > RTS Threshold: 2307
Security > Firewall > Block Anonymous WAN Access <--- Uncheck
  • 'buddee' suggested if you are having trouble doing a hard reset using the 30/30/30 method, you can try using the wrt320n hard reset method instead. It has been confirmed to work on the E2000 as well.
Unplug power cable
Hold down WPS button and plug power back in
Continue holding WPS button for 12 seconds, then release
  • The Broadcom 4717 SoC uses a default clock of 300MHz, but the Linksys E2000 runs at 354MHz. The increased heat can reduce routing performance, and may be responsible for many of the wireless errors reported in the forum. It is suggested that you either set the CPU clock to 300MHz, or add a heat sink and/or improve ventilation. BE SURE TO USE SPEEDTEST TO MEASURE THROUGHPUT PERFORMANCE BEFORE AND AFTER THIS CHANGE! HIGHER SPEED LINKS (50Mb/s down, etc.) MAY SEE REDUCED PERFORMANCE.
    • Open up a telnet or SSH prompt and login to your router. Type the following:
nvram set clkfreq=300,150,75
nvram commit && reboot

VLANs Support

It is also known for the E2000 to support VLANs. Also note that in order to adjust VLANs from the webgui with the E2000 then you will need build 15508 or better, which should be available through the above posted FTP links. Please refer to these wiki links for further info regarding configs.

http://www.dd-wrt.com/wiki/index.php/Switched_Ports

http://www.dd-wrt.com/wiki/index.php/VLAN_Support

Reverting back to stock firmware

It has been asked about how to revert back to stock firmware, why would you ever want to do that?!? You can always flash back to dd-wrt anyhow, to revert back to stock firmware simply download the latest E2000 firmware from linksys site, reset you router to defaults from within dd-wrt's webgui, wait, then login and select the stock firmware file and flash, make sure to select "reset to defaults" on the drop down menu when flashing.