Linksys E1550

From DD-WRT Wiki

(Difference between revisions)
Jump to: navigation, search
Revision as of 21:39, 3 September 2012 (edit)
Buddee (Talk | contribs)
(add hardware table)
← Previous diff
Revision as of 21:43, 3 September 2012 (edit) (undo)
Buddee (Talk | contribs)
(add flashing instructs)
Next diff →
Line 35: Line 35:
| 1 USB 2.0 Port | 1 USB 2.0 Port
|} |}
 +
 +
 += Flashing instructions for the E1550 =
 +
 +'''After using the trailed build file for the initial flash (yes the file with the router name in it) only use nv60k builds to upgrade with or you will brick your unit! '''
 +
 +# Read the [http://www.dd-wrt.com/phpBB2/viewtopic.php?t=51486 '''Peacock Announcement'''] carefully.
 +# Disconnect all cables and wireless clients.
 +# Do a [http://www.dd-wrt.com/wiki/index.php/Hard_reset_or_30/30/30 30/30/30] reset on router
 +# Connect 1 Lan cable to pc doing the flash.
 +# Log into Linkysys Web Interface Firmware Upgrade page at 192.168.1.1 and flash the firmware [ftp://ftp.dd-wrt.com//others/eko/BrainSlayer-V24-preSP2/2012/06-08-12-r19342/broadcom_K26/dd-wrt.v24-19342_NEWD-2_K2.6_mini-e1550.bin '''E1550 Trailed Initial Flash Build''']
 +# Wait 5 minutes to assure flash integrity.
 +# Power cycle by unplugging E1550 for 10 seconds.
 +# Plug the E1550 back in and wait about 2 minutes until it finishes booting.
 +# Do a [http://www.dd-wrt.com/wiki/index.php/Hard_reset_or_30/30/30 30/30/30] reset on router.
 +# Wait 3 minutes and log into web interface.
 +# You are done.
 +
 +*After the initial flash - should you want to flash to a build with more features you can use a k2.6 nv60k BIG or mega build or any of the other build flavors that are of your liking for features. I linked the nv60k BIG build below to give USB support as the initial trailed mini does not.
 +
 +ftp://ftp.dd-wrt.com/others/eko/BrainSlayer-V24-preSP2/2012/06-08-12-r19342/broadcom_K26/dd-wrt.v24-19342_NEWD-2_K2.6_big-nv60k.bin

Revision as of 21:43, 3 September 2012

Hardware Information

CPU Broadcom BCM5358U
CPU Speed 300 MHz
Flash ROM 16 MB
RAM 64 MB
Radio 2.4 GHz
WLAN Support b/g/n
WLAN Max Speed 300 mbps
Antenna Location Internal
N MIMO Config 2 Transmit x 3 Receieve
Switch 4x 10/100 LAN + 1 10/100 WAN
USB Port 1 USB 2.0 Port


Flashing instructions for the E1550

After using the trailed build file for the initial flash (yes the file with the router name in it) only use nv60k builds to upgrade with or you will brick your unit!

  1. Read the Peacock Announcement carefully.
  2. Disconnect all cables and wireless clients.
  3. Do a 30/30/30 reset on router
  4. Connect 1 Lan cable to pc doing the flash.
  5. Log into Linkysys Web Interface Firmware Upgrade page at 192.168.1.1 and flash the firmware E1550 Trailed Initial Flash Build
  6. Wait 5 minutes to assure flash integrity.
  7. Power cycle by unplugging E1550 for 10 seconds.
  8. Plug the E1550 back in and wait about 2 minutes until it finishes booting.
  9. Do a 30/30/30 reset on router.
  10. Wait 3 minutes and log into web interface.
  11. You are done.
  • After the initial flash - should you want to flash to a build with more features you can use a k2.6 nv60k BIG or mega build or any of the other build flavors that are of your liking for features. I linked the nv60k BIG build below to give USB support as the initial trailed mini does not.

ftp://ftp.dd-wrt.com/others/eko/BrainSlayer-V24-preSP2/2012/06-08-12-r19342/broadcom_K26/dd-wrt.v24-19342_NEWD-2_K2.6_big-nv60k.bin