Linksys E1550

From DD-WRT Wiki

(Difference between revisions)
Jump to: navigation, search
Revision as of 21:50, 3 September 2012 (edit)
Buddee (Talk | contribs)
(add pics)
← Previous diff
Revision as of 23:52, 22 September 2012 (edit) (undo)
Buddee (Talk | contribs)
(Hardware Information - add BCM5358 homelink reference)
Next diff →
Line 7: Line 7:
{| border="1" cellspacing="0" {| border="1" cellspacing="0"
! CPU ! CPU
-| Broadcom BCM5358U+| Broadcom [http://www.broadcom.com/products/Wireless-LAN/802.11-Wireless-LAN-Solutions/BCM5358x-Family BCM5358U]
|- |-
! CPU Speed ! CPU Speed
Line 39: Line 39:
| 1 USB 2.0 Port | 1 USB 2.0 Port
|} |}
- 
= Flashing instructions for the E1550 = = Flashing instructions for the E1550 =

Revision as of 23:52, 22 September 2012

Image:e1550f.jpg Image:e1550b.jpg


Hardware Information

CPU Broadcom BCM5358U
CPU Speed 300 MHz
Flash ROM 16 MB
RAM 64 MB
Radio 2.4 GHz
WLAN Support b/g/n
WLAN Max Speed 300 mbps
Antenna Location Internal
N MIMO Config 2 Transmit x 3 Receieve
Switch 4x 10/100 LAN + 1 10/100 WAN
USB Port 1 USB 2.0 Port

Flashing instructions for the E1550

After using the trailed build file for the initial flash (yes the file with the router name in it) only use nv60k builds to upgrade with or you will brick your unit!

  1. Read the Peacock Announcement carefully.
  2. Disconnect all cables and wireless clients.
  3. Do a 30/30/30 reset on router
  4. Connect 1 Lan cable to pc doing the flash.
  5. Log into Linkysys Web Interface Firmware Upgrade page at 192.168.1.1 and flash the firmware E1550 Trailed Initial Flash Build
  6. Wait 5 minutes to assure flash integrity.
  7. Power cycle by unplugging E1550 for 10 seconds.
  8. Plug the E1550 back in and wait about 2 minutes until it finishes booting.
  9. Do a 30/30/30 reset on router.
  10. Wait 3 minutes and log into web interface.
  11. You are done.
  • After the initial flash - should you want to flash to a build with more features you can use a k2.6 nv60k BIG or mega build or any of the other build flavors that are of your liking for features. I linked the nv60k BIG build below to give USB support as the initial trailed mini does not.

ftp://ftp.dd-wrt.com/others/eko/BrainSlayer-V24-preSP2/2012/06-08-12-r19342/broadcom_K26/dd-wrt.v24-19342_NEWD-2_K2.6_big-nv60k.bin


Build information

As noted in bold at the beginning of the flashing instructions, only use builds with nv60k in the name for upgrading - otherwise follow the initial flash instructions above if you are going from stock to dd-wrt, any other builds for upgrading an exsisting dd-wrt install without nv60k in the name will brick your router! This unit was supported with build 18946 or greater, this means you cannot use a build with a number lesser than 18946. For the safest results, use builds that are linked within this wiki as they have most likely been forum tested with ok reported results.

To find the latest builds, you can browse the DD-WRT file server and look for the broadcom_K26 folder, in there is the appropriate for your unit. Be aware that these are beta test builds and should be used with caution!

ftp://ftp.dd-wrt.com/others/eko/BrainSlayer-V24-preSP2