Linksys E1500

From DD-WRT Wiki

(Difference between revisions)
Jump to: navigation, search
Revision as of 22:57, 16 October 2016 (edit)
S2s2 (Talk | contribs)
(added a way to recover the router when stuck)
← Previous diff
Revision as of 23:37, 16 October 2016 (edit) (undo)
S2s2 (Talk | contribs)

Next diff →
Line 66: Line 66:
ftp://ftp.dd-wrt.com/betas ftp://ftp.dd-wrt.com/betas
-=Recovering from a bad flash (10/2016)=+=Recovering from a bad flash, or bad settings that send it into Management Mode Firmware Recovery (10/2016)=
-I've found these for five bucks at the local Goodwill, so they are worth toying with. I have <u>DD-WRT v3.0 r29519 mega (04/25/16)</u> running on it's cousin, the e1200, that's a K3X build. Works great!+The following is a brief overview for those familiar with flashing and recovery:
 +# You will have to load dd-wrt.v24-21061_NEWD-2_K2.6_mini-e1500.bin However it has a bug and your ethernet ports won't work. Earlier builds (maybe 19xxx) don't have this bug, but whatever.
 +# It will reflash and reboot, but then your ethernet ports won't work.
 +# From a good WiFi connection to DD-WRT (Open), flash FW_E1500_v1.0.06.001_US_20140327_code.bin (Linksys firmware)
 +# Rather than bothering with logging into the linksys management page over wifi, wait for it to stabilize then use a paperclip to press the reset button on the bottom. This triggers the right kind of reset that will get your ethernet ports working on the next reboot.
 +# With ethernet working again, go to the Linksys management page (http://192.168.1.1) and Administration, Firmware Update. Upload dd-wrt.v24-30731_NEWD-2_K3.x_mega-e1500.bin
-Sometimes when flashing or changing settings on /beta builds (K3X), you'll run into a boot where the power light will blink on a regular on-off about once a second. When you set a fixed IP on your ethernet port, and open http://192.168.1.1 you'll see something called a "Management Mode Firmware Recovery" screen. It's sort of like a tftp recovery, a basic web interface to upload a firmware.+It should be working after this. You may have to reset it once more, but I don't think I usually do.
-A couple of notes:+Long form:
 +I've found these for five bucks at the local Goodwill, so they are worth toying with. I have <u>DD-WRT v3.0 r29519 mega (04/25/16)</u> running on it's cousin in a production environment. On the e1200, that's a K3X build. Works great!
-* You only have a brief amount of time to begin your upload. Wait more than 30 seconds or so, and you will have to power down and up the router, refresh the screen, and try it again. Wait longer than 30 seconds, and the page is unresponsive, and won't accept uploads. When you are successful, on your Firefox status bar, it will show the upload progress (goes in a split second, very quickly on mini-build flashes), and then within seconds, the router goes to flashing the firmware, resetting, etc. You should definitely see something happening with the power light within 10 seconds, probably immediately. I use Firefox quite often to troubleshoot buggy networks or flaky connections to routers (over experimental links), because you can reduce the number of simultaneous connections opened by the browser to four. Chrome does not have this open <i>(although many people have asked for it, Google programmers have been typically arrogant over adding the option to adjust it down, and this also affects people with certain kinds of WAN links, that Chrome has a tendency to flood the number of available open connections. Google's response is to upgrade your hardware.)</i> Also Firefox has a status bar.+Sometimes when flashing or changing settings on /beta builds (K3X), you'll run into a boot where the power light will blink on a regular on-off about once a second. When you set a fixed IP on your ethernet port, and open http://192.168.1.1 you'll see something called a "Management Mode Firmware Recovery" screen. It's sort of like a tftp recovery, a basic web interface to upload a firmware.
-* '''You need this build:''' ftp://ftp.dd-wrt.com/betas/2013/03-25-2013-r21061/broadcom_K26/dd-wrt.v24-21061_NEWD-2_K2.6_mini-e1500.bin There are newer K3X builds in nv64k, but they do not flash through the Management Mode Recovery screen. Also, I was unable to flash to Linksys's own <i>(Ver.1.0.06 (Build 1) Latest Date: 04/25/2014</i> firmware. However, I found the 21061 build of dd-wrt worked great. (http://www.dd-wrt.com/phpBB2/viewtopic.php?p=887406)+A couple of notes:
 +* You only have a brief amount of time to begin your upload while in the Management Mode Recovery screen. Wait more than 20-30 seconds, and you will have to power down and up the router, refresh the screen, and try it again. Wait longer than 30 seconds, and the page is unresponsive, and won't accept uploads. When you are successful, on your Firefox status bar, it will show the upload progress (goes in a split second, very quickly on mini-build flashes), and then within seconds, the router goes to flashing the firmware, resetting, etc. You should definitely see something happening after the flash upload, with the power light, within 10 seconds, probably immediately. I use Firefox quite often to troubleshoot buggy networks or flaky connections to routers (over experimental links), because you can reduce the number of simultaneous connections opened by the browser to four. Chrome does not have this open <i>(although many people have asked for it, Google programmers have been typically arrogant over adding the option to adjust it down, and this also affects people with certain kinds of WAN links, that Chrome has a tendency to flood the number of available open connections. Google's response is to upgrade your hardware.)</i> Also Firefox has a status bar.
 +* '''You need this build:''' ftp://ftp.dd-wrt.com/betas/2013/03-25-2013-r21061/broadcom_K26/dd-wrt.v24-21061_NEWD-2_K2.6_mini-e1500.bin There are newer K3X builds in nv64k, but they do not flash via/through the Management Mode Recovery screen. Also, I was also unable to flash to Linksys's own <i>(Ver.1.0.06 (Build 1) Latest Date: 04/25/2014</i> firmware. However, I found the 21061 build of dd-wrt worked great. (http://www.dd-wrt.com/phpBB2/viewtopic.php?p=887406)
 +* Once you flash r21061, follow the instructions above.
=Reverting to stock firmware= =Reverting to stock firmware=
-It has been asked about: "how do i revert back to stock firmware?" and the answer is download the stock firmware image from the manufacturer's website, reset the router back to defaults using a 30-30-30 hard reset, then flash the stock image from within the dd-wrt webgui. After 5 minutes it should finish, you will then need to do another 30-30-30 reset and then access the stock webgui @ 192.168.1.1+It has been asked: "how do i revert back to stock firmware?" and the answer is download the stock firmware image from the manufacturer's website, reset the router back to defaults using a 30-30-30 hard reset, then flash the stock image from within the dd-wrt webgui. After 5 minutes it should finish, you will then need to do another 30-30-30 reset and then access the stock webgui @ 192.168.1.1
[[Category:Linksys]] [[Category:Linksys]]

Revision as of 23:37, 16 October 2016

Image:E1500frnt.jpg Image:E1500bak.jpg

Contents

Hardware Information

CPU Broadcom BCM5357
CPU Speed 300 MHz
Flash ROM 8 MB
RAM 32 MB
Radio 2.4 GHz
WLAN Support b/g/n
WLAN Max Speed 300 mbps
Antenna Location Internal
MIMO Config 2 Transmit x 3 Receieve
Switch 4x 10/100 LAN + 1 10/100 WAN
USB Port None

Flashing instructions for the E1500

After using the trailed build file for the initial flash (yes the file with the router name in it) only use nv64k builds to upgrade with or you will brick your unit. Don't confuse this unit with some of the other Linksys E-Series units that use nv60k builds, this one uses nv64k builds!

  1. Read the Peacock Announcement carefully.
  2. Disconnect all cables and wireless clients.
  3. Do a 30/30/30 reset on router
  4. Connect 1 Lan cable to pc doing the flash.
  5. Log into Linkysys Web Interface Firmware Upgrade page at 192.168.1.1 and flash the firmware E1500 Trailed Initial Flash Build
  6. Wait 5 minutes to assure flash integrity.
  7. Power cycle by unplugging the E1500 for 10 seconds.
  8. Plug the E1500 back in and wait about 2 minutes until it finishes booting.
  9. Do a 30/30/30 reset on router. Another power cycle may be required after the hard reset as noted by some forum users.
  10. Wait 3 minutes and log into web interface.
  11. Start configuring and using dd-wrt.
  • After the initial flash - should you want to flash to a build with more features you can use a k2.6 nv64k BIG or mega build or any of the other build flavors that are of your liking for features - so long as they fit into the 8 meg flash, flashing builds bigger than 8 meg may result in flash failure or even worse, may BRICK so be watchful of build file sizes that you download.

ftp://ftp.dd-wrt.com/others/eko/BrainSlayer-V24-preSP2/2013/05-27-2013-r21676/broadcom_K26/dd-wrt.v24-21676_NEWD-2_K2.6_big-nv64k.bin

Build information

As noted in bold at the beginning of the flashing instructions, only use builds with nv64k in the name for upgrading - otherwise follow the initial flash instructions above if you are going from stock to dd-wrt, any other builds for upgrading an existing dd-wrt install without nv64k in the name will brick your router! This unit was supported with build 18946 or greater, this means you cannot use a build with a number lesser than 18946. For the safest results, use builds that are linked within this wiki as they have most likely been forum tested with ok reported results.

To find the latest builds, you can browse the DD-WRT ftp server.

ftp://ftp.dd-wrt.com/betas

Recovering from a bad flash, or bad settings that send it into Management Mode Firmware Recovery (10/2016)

The following is a brief overview for those familiar with flashing and recovery:

  1. You will have to load dd-wrt.v24-21061_NEWD-2_K2.6_mini-e1500.bin However it has a bug and your ethernet ports won't work. Earlier builds (maybe 19xxx) don't have this bug, but whatever.
  2. It will reflash and reboot, but then your ethernet ports won't work.
  3. From a good WiFi connection to DD-WRT (Open), flash FW_E1500_v1.0.06.001_US_20140327_code.bin (Linksys firmware)
  4. Rather than bothering with logging into the linksys management page over wifi, wait for it to stabilize then use a paperclip to press the reset button on the bottom. This triggers the right kind of reset that will get your ethernet ports working on the next reboot.
  5. With ethernet working again, go to the Linksys management page (http://192.168.1.1) and Administration, Firmware Update. Upload dd-wrt.v24-30731_NEWD-2_K3.x_mega-e1500.bin

It should be working after this. You may have to reset it once more, but I don't think I usually do.

Long form: I've found these for five bucks at the local Goodwill, so they are worth toying with. I have DD-WRT v3.0 r29519 mega (04/25/16) running on it's cousin in a production environment. On the e1200, that's a K3X build. Works great!

Sometimes when flashing or changing settings on /beta builds (K3X), you'll run into a boot where the power light will blink on a regular on-off about once a second. When you set a fixed IP on your ethernet port, and open http://192.168.1.1 you'll see something called a "Management Mode Firmware Recovery" screen. It's sort of like a tftp recovery, a basic web interface to upload a firmware.

A couple of notes:

  • You only have a brief amount of time to begin your upload while in the Management Mode Recovery screen. Wait more than 20-30 seconds, and you will have to power down and up the router, refresh the screen, and try it again. Wait longer than 30 seconds, and the page is unresponsive, and won't accept uploads. When you are successful, on your Firefox status bar, it will show the upload progress (goes in a split second, very quickly on mini-build flashes), and then within seconds, the router goes to flashing the firmware, resetting, etc. You should definitely see something happening after the flash upload, with the power light, within 10 seconds, probably immediately. I use Firefox quite often to troubleshoot buggy networks or flaky connections to routers (over experimental links), because you can reduce the number of simultaneous connections opened by the browser to four. Chrome does not have this open (although many people have asked for it, Google programmers have been typically arrogant over adding the option to adjust it down, and this also affects people with certain kinds of WAN links, that Chrome has a tendency to flood the number of available open connections. Google's response is to upgrade your hardware.) Also Firefox has a status bar.
  • You need this build: ftp://ftp.dd-wrt.com/betas/2013/03-25-2013-r21061/broadcom_K26/dd-wrt.v24-21061_NEWD-2_K2.6_mini-e1500.bin There are newer K3X builds in nv64k, but they do not flash via/through the Management Mode Recovery screen. Also, I was also unable to flash to Linksys's own (Ver.1.0.06 (Build 1) Latest Date: 04/25/2014 firmware. However, I found the 21061 build of dd-wrt worked great. (http://www.dd-wrt.com/phpBB2/viewtopic.php?p=887406)
  • Once you flash r21061, follow the instructions above.

Reverting to stock firmware

It has been asked: "how do i revert back to stock firmware?" and the answer is download the stock firmware image from the manufacturer's website, reset the router back to defaults using a 30-30-30 hard reset, then flash the stock image from within the dd-wrt webgui. After 5 minutes it should finish, you will then need to do another 30-30-30 reset and then access the stock webgui @ 192.168.1.1