Linksys E1200v2

From DD-WRT Wiki

(Difference between revisions)
Jump to: navigation, search
Revision as of 14:57, 24 October 2014 (edit)
JNavas (Talk | contribs)
(Kong mirror)
← Previous diff
Revision as of 15:49, 13 March 2015 (edit) (undo)
JNavas (Talk | contribs)
(More Information - update Kong)
Next diff →
Line 78: Line 78:
'''Good build for this device is [ 21676 mini].''' ''Larger 21676 builds have the [ Heartbleed vulnerability]!'' '''Good build for this device is [ 21676 mini].''' ''Larger 21676 builds have the [ Heartbleed vulnerability]!''
-If you must have more features than mini, try the latest '''[ Kong builds]''' (e.g., [ 22000++]).+If you must have more features than mini, try '''[ Kong 22000++].
- +
=Reverting to Stock Firmware= =Reverting to Stock Firmware=

Revision as of 15:49, 13 March 2015

This page applies to version 2. For version 1, see Linksys E1200


Hardware Information

CPU Broadcom BCM5357
CPU Speed 300 MHz
Flash ROM 8 MB
Radio 2.4 GHz
WLAN Support b/g/n
WLAN Max Speed 300 mbps
Antenna Location Internal
Switch 4x 10/100 LAN + 1 10/100 WAN
USB Port None

Flashing Instructions

After using the trailed build file for the initial flash (yes the file with the router name in it) only use nv64k builds to upgrade with or you will brick your unit. Don't confuse this unit with some of the other Linksys E-Series units that use nv60k builds, this one uses nv64k builds!

  1. Read the Peacock Announcement carefully.
  2. Disconnect all cables and wireless clients.
  3. Do a 30/30/30 reset on router
  4. Connect 1 Lan cable to pc doing the flash and plug the other end into one of the router's switch ports. Do not use the WAN port for flashing, it won't work.
  5. Log into Linkysys Web Interface Firmware Upgrade page at and flash the firmware E1200v2 Trailed Initial Flash Build
  6. Wait 5 minutes to assure flash integrity.
  7. Power cycle by unplugging the E1200v2 for 5 seconds.
  8. Plug the E1200v2 back in and wait about 2 minutes until it finishes booting.
  9. Do a 30/30/30 reset on router. As reported from the forum, an additional power cycle after the 30-30-30 may be required as well.
  10. Wait 3 minutes and log into web interface.
  11. You are done.
  • After the initial flash - should you want to flash to a build with more features you can use a k2.6 nv64k BIG or mega build or any of the other build flavors that are of your liking for features.

Build Information

As noted in bold at the beginning of the flashing instructions, only use builds with nv64k in the name for upgrading - otherwise follow the initial flash instructions above if you are going from stock to dd-wrt, any other builds for upgrading an exsisting dd-wrt install without nv64k in the name will brick your router! This unit was supported with build 18946 or greater, this means you cannot use a build with a number lesser than 18946. For the safest results, use builds that are linked within this wiki as they have most likely been forum tested with ok reported results.

To find the latest builds, you can browse the DD-WRT file server and look for the broadcom_K26 folder, in there is the appropriate for your unit. Be aware that these are beta test builds and should be used with caution!

As of the 19519 build, mega and big have become to overgrown to fit within an 8MB flash, always check the build sizes, this unit can only allow for an 8MB footprint, so if the file is larger than around 7.9MB, it will not work

More Information

Forum thread:

Good build for this device is 21676 mini. Larger 21676 builds have the Heartbleed vulnerability!

If you must have more features than mini, try Kong 22000++.

Reverting to Stock Firmware

Download the stock firmware image from the manufacturer's website (link), reset the router back to defaults using a 30-30-30 hard reset, then flash the stock image from within the dd-wrt webgui. After 5 minutes it should finish, you will then need to do another 30-30-30 reset and then access the stock webgui @