Linksys E1200v2
From DD-WRT Wiki
Revision as of 17:07, 25 December 2012 (edit) Buddee (Talk | contribs) ← Previous diff |
Revision as of 17:03, 5 June 2018 (edit) (undo) Jeremywh7 (Talk | contribs) Next diff → |
||
(43 intermediate revisions not shown.) | |||
Line 1: | Line 1: | ||
- | = | + | <span style="color:red">'''This page applies to version 2.'''</span> For version 1, see [[Linksys E1200]] |
+ | [[Image:E1200 Photo01.jpg | right | 350px]] | ||
+ | =Hardware [https://wikidevi.com/wiki/Linksys_E1200_v2 Information]= | ||
{| border="1" cellspacing="0" | {| border="1" cellspacing="0" | ||
! CPU | ! CPU | ||
- | | Broadcom | + | | Broadcom BCM5357 |
|- | |- | ||
! CPU Speed | ! CPU Speed | ||
| 300 MHz | | 300 MHz | ||
|- | |- | ||
- | ! Flash ROM | + | ! RAM/Flash ROM |
- | | 8 MB | + | | 32 MB / 8 MB [1] |
- | + | ||
- | + | ||
- | + | ||
|- | |- | ||
! Radio | ! Radio | ||
Line 21: | Line 20: | ||
|- | |- | ||
! WLAN Max Speed | ! WLAN Max Speed | ||
- | | 300 | + | | 300 Mb/s |
|- | |- | ||
! Antenna Location | ! Antenna Location | ||
| Internal | | Internal | ||
|- | |- | ||
- | ! Switch | + | ! Switch Ports |
- | | | + | | 4 LAN/1 WAN (10/100 Mb/s) |
|- | |- | ||
! USB Port | ! USB Port | ||
| None | | None | ||
|} | |} | ||
+ | [1] - E1200v2 [http://www.dd-wrt.com/phpBB2/viewtopic.php?p=1098154#1098154 has 64 KB more than most 8MB routers]: 8060928 bytes (7872 KB).<br> | ||
+ | '''Do NOT flash larger builds!''' | ||
- | = Flashing | + | = Flashing Instructions = |
- | + | *Download the initial flash trailed build: [ftp://ftp.dd-wrt.com/betas/2012/07-20-12-r19519/broadcom_K26/dd-wrt.v24-19519_NEWD-2_K2.6_mini-e1200v2.bin 19519 K2.6 mini e1200v2] is known to work | |
- | ''' | + | *Download an '''nv64k''' Upgrade build: K3X is recommended (see [[Index:FAQ#Where_do_I_download_firmware.3F|Where do I download firmware?]]) |
- | + | '''WARNING:''' only use ''nv64k'' builds. Don't confuse this with other Linksys E-Series units use nv60k builds!<br> | |
- | + | *These instructions were performed with an e1200v2 running FW_E1200_v2.0.07.002_US_20150108.bin | |
- | # | + | #With a wired connection, log into the [http://192.168.1.1 Linksys Web Interface] Firmware Upgrade page. |
- | + | #Do a reset using the stock web interface. Wait a minute. | |
- | + | #Flash the initial flash firmware: dd-wrt.v24-19519_NEWD-2_K2.6_mini-e1200v2.bin | |
- | + | #Wait 2 minutes for the router to flash and reboot itself. | |
- | # Wait | + | #Wait about another 2 minutes until it finishes booting. |
- | # | + | #Log into the [http://192.168.1.1 dd-wrt web interface] and set a password |
- | + | #Flash the Upgrade build and then reset using the GUI | |
- | # | + | #*Wait 3-4 minutes for the flash to complete, then if isn't accessible, manually power cycle the router |
- | # Wait 3 minutes | + | |
- | + | ||
- | + | ||
- | + | ||
- | + | For download links, build information, and more: [[Index:FAQ#Where_do_I_download_firmware.3F|Where do I download firmware?]] | |
- | + | Minimum build with the Broadcom krack fixes is 33772. See [[KRACK_Vulnerability_and_DD-WRT|here]] for more info. | |
- | + | =No LAN ports After Reset= | |
+ | There is a persistent bug with some E-series routers in DD-WRT after a reset, where the LAN-ethernet ports are not bound to anything, and only wireless (WLAN) is working initially. | ||
- | + | '''Fix:''' access the web interface '''using wireless''' and add vlan1 (ethernet ports) back to the bridge. | |
+ | *For a step-by-step and more details see [[Linksys_E1500#No_Ethernet.2C_LAN_port_connection|here.]] | ||
- | ftp://ftp.dd-wrt.com/others/eko/BrainSlayer-V24-preSP2 | ||
- | + | =Recovering from Management Recovery Mode= | |
+ | Follow the [[Linksys_E1500#Management_Mode_Recovery|E1500 directions]], substituting e1500 for e1200v2 and using the appropriate firmware. | ||
- | =Reverting to stock firmware | + | =Reverting to Stock Firmware= |
+ | Download the stock firmware image from the manufacturer's website ([http://support.linksys.com/en-us/support/routers/E1200 link]), reset the router back to defaults using a 30-30-30 hard reset, then flash the stock image from within the dd-wrt webgui. After 5 minutes it should finish, you will then need to do another 30-30-30 reset and then access the stock webgui @ 192.168.1.1 | ||
- | + | [[Category:Linksys]] |
Revision as of 17:03, 5 June 2018
This page applies to version 2. For version 1, see Linksys E1200
Contents |
Hardware Information
CPU | Broadcom BCM5357 |
---|---|
CPU Speed | 300 MHz |
RAM/Flash ROM | 32 MB / 8 MB [1] |
Radio | 2.4 GHz |
WLAN Support | b/g/n |
WLAN Max Speed | 300 Mb/s |
Antenna Location | Internal |
Switch Ports | 4 LAN/1 WAN (10/100 Mb/s) |
USB Port | None |
[1] - E1200v2 has 64 KB more than most 8MB routers: 8060928 bytes (7872 KB).
Do NOT flash larger builds!
Flashing Instructions
- Download the initial flash trailed build: 19519 K2.6 mini e1200v2 is known to work
- Download an nv64k Upgrade build: K3X is recommended (see Where do I download firmware?)
WARNING: only use nv64k builds. Don't confuse this with other Linksys E-Series units use nv60k builds!
- These instructions were performed with an e1200v2 running FW_E1200_v2.0.07.002_US_20150108.bin
- With a wired connection, log into the Linksys Web Interface Firmware Upgrade page.
- Do a reset using the stock web interface. Wait a minute.
- Flash the initial flash firmware: dd-wrt.v24-19519_NEWD-2_K2.6_mini-e1200v2.bin
- Wait 2 minutes for the router to flash and reboot itself.
- Wait about another 2 minutes until it finishes booting.
- Log into the dd-wrt web interface and set a password
- Flash the Upgrade build and then reset using the GUI
- Wait 3-4 minutes for the flash to complete, then if isn't accessible, manually power cycle the router
For download links, build information, and more: Where do I download firmware?
Minimum build with the Broadcom krack fixes is 33772. See here for more info.
No LAN ports After Reset
There is a persistent bug with some E-series routers in DD-WRT after a reset, where the LAN-ethernet ports are not bound to anything, and only wireless (WLAN) is working initially.
Fix: access the web interface using wireless and add vlan1 (ethernet ports) back to the bridge.
- For a step-by-step and more details see here.
Recovering from Management Recovery Mode
Follow the E1500 directions, substituting e1500 for e1200v2 and using the appropriate firmware.
Reverting to Stock Firmware
Download the stock firmware image from the manufacturer's website (link), reset the router back to defaults using a 30-30-30 hard reset, then flash the stock image from within the dd-wrt webgui. After 5 minutes it should finish, you will then need to do another 30-30-30 reset and then access the stock webgui @ 192.168.1.1