Linksys E1200
From DD-WRT Wiki
Revision as of 21:58, 19 October 2016 (edit) S2s2 (Talk | contribs) ← Previous diff |
Revision as of 14:15, 12 February 2018 (edit) (undo) Jeremywh7 (Talk | contribs) Next diff → |
||
Line 8: | Line 8: | ||
{| border="1" cellspacing="0" | {| border="1" cellspacing="0" | ||
! CPU | ! CPU | ||
- | | Broadcom [ | + | | Broadcom [https://wikidevi.com/wiki/Linksys_E1200_v1 BCM5357] |
|- | |- | ||
! CPU Speed | ! CPU Speed | ||
Line 31: | Line 31: | ||
| Internal | | Internal | ||
|- | |- | ||
- | ! Switch | + | ! LAN / WAN Switch Ports |
- | | | + | | 4/1 (10/100 Mb/s) |
|- | |- | ||
! USB Port | ! USB Port | ||
Line 41: | Line 41: | ||
= Flashing Instructions = | = Flashing Instructions = | ||
- | + | After using the initial flash trailed build (the file with the router name in it), '''only use nv64k builds to upgrade''' with or you will brick your unit. Don't confuse this unit with some other Linksys E-Series units that use nv60k builds! | |
# Read the [http://www.dd-wrt.com/phpBB2/viewtopic.php?t=51486 '''Peacock Announcement'''] carefully. | # Read the [http://www.dd-wrt.com/phpBB2/viewtopic.php?t=51486 '''Peacock Announcement'''] carefully. | ||
# Disconnect all cables and wireless clients. | # Disconnect all cables and wireless clients. | ||
- | # Do a [http://www.dd-wrt.com/wiki/index.php/Hard_reset_or_30/30/30 | + | # Do a [http://www.dd-wrt.com/wiki/index.php/Hard_reset_or_30/30/30 hard] reset on router |
- | # Connect | + | # Connect a LAN cable to the PC doing the flash. |
- | # Log into | + | # Log into [http://192.168.1.1 Linksys Web Interface] Firmware Upgrade page |
+ | # Upload the known good initial flash [ftp://ftp.dd-wrt.com/betas/2013/05-27-2013-r21676/broadcom_K26/dd-wrt.v24-21676_NEWD-2_K2.6_mini-e1200v1.bin '''E1200 (v1) Trailed Build'''] | ||
# Wait 5 minutes to assure flash integrity. | # Wait 5 minutes to assure flash integrity. | ||
# Power cycle by unplugging the E1200 for 5 seconds. | # Power cycle by unplugging the E1200 for 5 seconds. | ||
Line 55: | Line 56: | ||
# You are done. | # You are done. | ||
- | * ''' | + | * '''WARNING:''' only use nv64k builds that fit a 4MB flash footprint, bigger builds can either fail or brick your unit. |
=Build Information= | =Build Information= | ||
- | + | '''Support for this model was added with build 18946, so do not use any older builds.''' To be safe, only use builds that are linked within this wiki, or otherwise read New Build and model-specific [https://www.dd-wrt.com/phpBB2/viewforum.php?f=1 forum threads]. To find the latest builds, look [ftp://ftp.dd-wrt.com/betas/ here] in broadcom_K26 folders. | |
- | ''' | + | |
- | + | ||
- | To find the latest builds, | + | |
- | + | ||
- | ftp://ftp.dd-wrt.com/betas/ | + | |
=More Information= | =More Information= | ||
- | + | '''Forum thread''': [http://www.dd-wrt.com/phpBB2/viewtopic.php?t=153302 for early E-Series] routers. | |
- | + | ||
- | + | ||
- | '''Forum thread''': http://www.dd-wrt.com/phpBB2/viewtopic.php?t=153302 | + | |
=Reverting to Stock Firmware= | =Reverting to Stock Firmware= | ||
- | + | Download the stock firmware image from the manufacturer's website, reset the router back to defaults using a 30-30-30 hard reset, then flash the stock image from within the dd-wrt webgui. After 5 minutes it should finish, you will then need to do another 30-30-30 reset and then access the stock webgui @ 192.168.1.1 | |
- | + | ||
[[Category:Linksys]] | [[Category:Linksys]] |
Revision as of 14:15, 12 February 2018
This page applies to version 1. For version 2, see Linksys E1200v2
Contents |
Hardware Information
CPU | Broadcom BCM5357 |
---|---|
CPU Speed | 300 MHz |
Flash ROM | 4 MB |
RAM | 32 MB |
Radio | 2.4 GHz |
WLAN Support | b/g/n |
WLAN Max Speed | 300 mbps |
Antenna Location | Internal |
LAN / WAN Switch Ports | 4/1 (10/100 Mb/s) |
USB Port | None |
Flashing Instructions
After using the initial flash trailed build (the file with the router name in it), only use nv64k builds to upgrade with or you will brick your unit. Don't confuse this unit with some other Linksys E-Series units that use nv60k builds!
- Read the Peacock Announcement carefully.
- Disconnect all cables and wireless clients.
- Do a hard reset on router
- Connect a LAN cable to the PC doing the flash.
- Log into Linksys Web Interface Firmware Upgrade page
- Upload the known good initial flash E1200 (v1) Trailed Build
- Wait 5 minutes to assure flash integrity.
- Power cycle by unplugging the E1200 for 5 seconds.
- Plug the E1200 back in and wait about 2 minutes until it finishes booting.
- Do a 30/30/30 reset on router.
- Wait 3 minutes and log into web interface.
- You are done.
- WARNING: only use nv64k builds that fit a 4MB flash footprint, bigger builds can either fail or brick your unit.
Build Information
Support for this model was added with build 18946, so do not use any older builds. To be safe, only use builds that are linked within this wiki, or otherwise read New Build and model-specific forum threads. To find the latest builds, look here in broadcom_K26 folders.
More Information
Forum thread: for early E-Series routers.
Reverting to Stock Firmware
Download the stock firmware image from the manufacturer's website, reset the router back to defaults using a 30-30-30 hard reset, then flash the stock image from within the dd-wrt webgui. After 5 minutes it should finish, you will then need to do another 30-30-30 reset and then access the stock webgui @ 192.168.1.1