LaFonera Hardware Replace LEDs (fr)

From DD-WRT Wiki

Revision as of 08:08, 6 April 2007 by Microbug (Talk | contribs)
Jump to: navigation, search

You are here: DD-WRT wiki mainpage / LaFonera / Hardware / Replace LEDs

english deutsch français

Contents

Remplacer les LEDs vertes

Aujourd'hui nous allons voir comment remplacer les LEDs vertes de LaFonera par des bleues.

Presque tout dans mon environnement (mise à part mon amie) a des LEDs bleues: PC, enceintes, voitures...
J'ai donc décidé de changer la couleur des LEDs de LaFonera.

Je pense que c'est une modification très simple, si vous savez bien manier un fer à souder.

Préparation

Voici le matériel que vous devez rassembler avant de commencer:

  • 3 nouvelles LEDs (les originales sont en 2,2V, mais les 3,3V marchent également)
  • fer à souder (panne très fine)
  • étain (le plus fin que vous puissiez trouver)
  • pinces
  • cutter
  • une heure de temps libre (si vous voulez faire les choses correctement, vous devez prendre votre temps)


Matériel de travail

image:LaFonera_Hardware_Replace_LEDs_-_08_preparation.jpg

Version haute définition

Guide étape par étape

Les LEDs d'origine

Voici votre poste de travail. Vous allez travailler sur ce côté du PCB de LaFonera pendant la prochaîne heure.

LEDs originales - off

image:LaFonera_Hardware_Replace_LEDs_-_01_original_green_leds_-_off.jpg

Version haute résolution


LEDs originales - on

image:LaFonera_Hardware_Replace_LEDs_-_02_original_green_leds_-_on.jpg

Version haute résolution

Removing these unwanted things

First you have to desolder the old LEDs. Be careful not to destroy the fine veins on the PCB.

  • Lay your knife under the first LED and warm up one side of it so you can press this side of the LED away from the PCB.
  • Then take your forceps to remove the LED after you warmed up the other side.
  • Take your soldering iron again to plane the tin on the PCB. This is important if you want to place the new LED in a plane position.

Repeat these steps two more times!

now your Fonera is without any lights


Original green LEDs removed

image:LaFonera_Hardware_Replace_LEDs_-_03_without_leds.jpg

view in high resolution


Soldering the new (very ingenious, hot, blue) LEDs

Before you start please note the position of the plus pole of the old LEDs. It is on the right side of them (if you have all three LEDs to your body - LAN and AC connection away from your body). All LEDs have a small point, line or a cut edge at the side of the plus-pole.

You can also test the new LEDs before you solder them. Just take them with your forceps onto the newly clean connections for the LEDs. Now you know in which direction you have to solder them (maybe you did before - but now you are sure).

  • Place the first LED carefully on the PCB in the middle of this little white frame printed on the PCB.
  • warm up your soldering iron and heat one side of the LED carefully (there are very small items near the LEDs - so be careful!)

at this time you can relocate the new LED, so it is in the right position

  • Now heat up the other side of the LED shortly. The tin on the pcb and some more tin on your soldering iron should be enough to fix it strongly.

That’s it. You have soldered your first new LED on your LaFonera. Repeat these three steps and you only have to clean up your workspace before you have finished your work.


The new blue LEDs - off

image:LaFonera_Hardware_Replace_LEDs_-_09_blue_leds_-_off.jpg

view in high resolution


The new blue LEDs - on

image:LaFonera_Hardware_Replace_LEDs_-_04_blue_leds_-_on.jpg

view in high resolution


Outside - detail of the LEDs

image:LaFonera_Hardware_Replace_LEDs_-_05_blue_leds_-_case_detail.jpg

view in high resolution


Inside - complete PCB

image:LaFonera_Hardware_Replace_LEDs_-_06_blue_leds_-_inside.jpg

view in high resolution


Outside view of the finished work

image:LaFonera_Hardware_Replace_LEDs_-_07_blue_leds_-_case.jpg

view in high resolution

Possibilités avancées/ Conseils de travail

Couleur des LEDs

Vous pouvez utiliser des LEDs de différentes couleurs.

jaune, rouge, bleue,

ou alors une seule et même couleur pour les 3 LEDs, comme vous voulez !

Conseil pour souder avec un gros fer

Si votre fer à souder est trop gros pour les petites LEDs, vous pouvez attacher un trombone sur celui-ci. Cela vous donne la possibilité de travailler bien plus précisemment avec ces petites pièces. Si vous mettez un peu d'étain sur la connection entre le fer à souder et le trombonne, la chaleur sera bien mieux transmise. Faites attention à attacher solidement le trombonne sur le fer, pour être sûr qu'il ne bougera pas pendant votre travail. Pensez à tester le système avant d'attaquer les choses sérieuses.

Attacher un trombone sur votre fer à souder

image:LaFonera_Hardware_Replace_LEDs_-_10_soldering_tip.jpg

Version haute résolution


Article rédigé par wildblue!
Traduit en français par Microbug 09:42, 6 Apr 2007 (CEST)