JTAG pinouts
From DD-WRT Wiki
Revision as of 14:42, 6 February 2010 (edit) Donny (Talk | contribs) (DWL2100/2200) ← Previous diff |
Revision as of 14:46, 6 February 2010 (edit) (undo) Donny (Talk | contribs) Next diff → |
||
Line 2: | Line 2: | ||
__TOC__ | __TOC__ | ||
+ | |||
+ | ==Airlink AR430W== | ||
+ | <center> | ||
+ | [[Image:AR430W.jpg]] | ||
+ | </center><br> | ||
+ | |||
+ | The router follows the MIPS 2.6 EJTAG Specification and has the same PIN information. But on the board the PINS are layed out as<br><br> | ||
+ | 1 2 3 4 5 6 7 <br> | ||
+ | 14 13 12 11 10 9 8 | ||
+ | <br><br> | ||
+ | 1 - nTRST<br> | ||
+ | 3 - TDI<br> | ||
+ | 5 - TDO<br> | ||
+ | 7 - TMS<br> | ||
+ | 9 - TCK<br> | ||
+ | 2, 4, 6, 8, 10 - GND [you only need one GND for JTAG]<br> | ||
+ | You dont need the following pins<br> | ||
+ | 11 - nSRST<br> | ||
+ | 14 - VCC<br> | ||
+ | 12, 13 - N/C<br> | ||
+ | |||
+ | ==Airlink AP431W== | ||
+ | |||
+ | Same as DWL-2100/2200 - See below | ||
==Asus WL500g Deluxe== | ==Asus WL500g Deluxe== | ||
Line 64: | Line 88: | ||
[http://www.jtagtest.com/pinouts/ejtag Standard v2.6 EJTAG connector]: | [http://www.jtagtest.com/pinouts/ejtag Standard v2.6 EJTAG connector]: | ||
+ | |||
+ | [[Image:4-FONERA_2200A_JTAG_v2.6.jpg]] | ||
Line 134: | Line 160: | ||
Nice German HowTo: [http://blog.digital4media.de/2006/04/jtag-adapter-fur-siemens-se505/ JTAG for SE505 v2] | Nice German HowTo: [http://blog.digital4media.de/2006/04/jtag-adapter-fur-siemens-se505/ JTAG for SE505 v2] | ||
<br><br> | <br><br> | ||
- | ==Airlink AR430W== | ||
- | <center> | ||
- | [[Image:AR430W.jpg]] | ||
- | </center><br> | ||
- | |||
- | The router follows the MIPS 2.6 EJTAG Specification and has the same PIN information. But on the board the PINS are layed out as<br><br> | ||
- | 1 2 3 4 5 6 7 <br> | ||
- | 14 13 12 11 10 9 8 | ||
- | <br><br> | ||
- | 1 - nTRST<br> | ||
- | 3 - TDI<br> | ||
- | 5 - TDO<br> | ||
- | 7 - TMS<br> | ||
- | 9 - TCK<br> | ||
- | 2, 4, 6, 8, 10 - GND [you only need one GND for JTAG]<br> | ||
- | You dont need the following pins<br> | ||
- | 11 - nSRST<br> | ||
- | 14 - VCC<br> | ||
- | 12, 13 - N/C<br> | ||
---- | ---- |
Revision as of 14:46, 6 February 2010
Airlink AR430W
The router follows the MIPS 2.6 EJTAG Specification and has the same PIN information. But on the board the PINS are layed out as
1 2 3 4 5 6 7
14 13 12 11 10 9 8
1 - nTRST
3 - TDI
5 - TDO
7 - TMS
9 - TCK
2, 4, 6, 8, 10 - GND [you only need one GND for JTAG]
You dont need the following pins
11 - nSRST
14 - VCC
12, 13 - N/C
Airlink AP431W
Same as DWL-2100/2200 - See below
Asus WL500g Deluxe
Asus WL500g Deluxe
Belkin_F5D7230_v1000
To flash use latest wrt54g v4.8, with these parameters: /fc:29 /nocwd /nobreak /noreset
watch out for RA11 (under the minipci)
Belkin_F5D7231_v1212
Buffalo WBR-G54
jtag is pins 1-12 (normal jtag pinout: 3: TDI, 5: TDO, 7: TMS, 9: TCK)
| |mini-pci card
| |_______________
| 2 12 JP1
| o o o o o o |o o|
| o o o o o o |o o|
| 1 11 JP2
Buffalo WLA-G54
siehe
[Buffalo WBR-G54]
Buffalo WLA-G54C
Buffalo WVR-G54-NF
Dell Truemobile 2300 v1
DLink DWL2100/2200
(Also Airlink AP321W)
Pin 1 to pin 14 Pin 3 TDI Pin 5 TDO Pin 7 TMS Pin 9 TCK Pin 6 Grd
Standard v2.6 EJTAG connector:
Fonera 2200A
Standard v2.6 EJTAG connector:
Linksys WRT300n v2
Linksys WRT54G v2
Motorola WE800G v1
Motorola WR850G v1
Parallel port - TJTAG 3.0.2 - /cable:wiggler
To get the Universal JTAG board, read this forum thread
Philips SNB6500 (v1)
Board before MOD: Image:1-SNB6500 BOARD.jpg Preparation: 1st step Preparation: 1st step First group of pads: Wires connected: Wires flow: Hidden connections: Second group of pads: Wires connected: Final look:
Siemens SE505 v1
see [Belkin_F5D7230_v1000]
Siemens SE505 v2
You will find round Labels on the flash chip with 01, 02, 03
Nice German HowTo: JTAG for SE505 v2
I updated the jtagspi with a 8Meg winbond flash and added information if you have to fix the code to match your JTAG hardware
jtagspi.tgz with my modifications