Instalación

From DD-WRT Wiki

(Difference between revisions)
Jump to: navigation, search
Revision as of 01:48, 22 June 2006 (edit)
Taguapire (Talk | contribs)

← Previous diff
Revision as of 01:52, 22 June 2006 (edit) (undo)
Taguapire (Talk | contribs)

Next diff →
Line 39: Line 39:
Otras marcas y modelos han sido mencionados como soportados por BrainSlayer y otros en el foro. Sin embargo, no esta claro si hay alguna imágen facilmente obtenible, que funcione en estos modelos, o si has preguntado a BrainSlayer directamente por estos, o si has obtenido el código fuente y los has compilado tu mismo. Sería genial si alguien que haya echo esto, editara esta página del Wiki más adelante. Otras marcas y modelos han sido mencionados como soportados por BrainSlayer y otros en el foro. Sin embargo, no esta claro si hay alguna imágen facilmente obtenible, que funcione en estos modelos, o si has preguntado a BrainSlayer directamente por estos, o si has obtenido el código fuente y los has compilado tu mismo. Sería genial si alguien que haya echo esto, editara esta página del Wiki más adelante.
 +
 +==Precauciones==
 +
 +Sigue todas las instrucciones al pie de la letra. Tendrás problemas si no lo haces.
 +
 +
 +*''' Incorrect flashing procedure can [[bricked|brick]] your router!'''
 +*''' You CANNOT flash/backup your firmware over a "https" connection!'''
 +* Firmware flashes and upgrade should be done over a '''wired''' Ethernet connection.
 +** Flashing via wireless is inherently unstable and can result in a [[bricked]] router.''
 +* Disable your anti-virus-software, as a false-positive virus detection could interrupt the upload.
 +* Disable any wireless adapters on your system to ensure that the upload goes through the wired connection!
 +* You will not have/need internet access from steps 2 through 5.
 +* We recommend you save this webpage and the webpages on how to [[Recover from a Bad Flash]] to your hard drive (File - Save Page As, '''*NOT* a bookmark'''). This will allow you to review the information offline in the event that something goes wrong.
 +
 +==Instalación vía TFTP==
 +This procedure must not be seen as the standard procedure for flashing: only use it when you are specifically told to do so (for example in the specific instructions for flashing your brand or type of device).
 +
 +Normally, the GUI flashing method should be used: it should be perfectly adequate for any standard situation. See that section for more information.
 +
 +(more info to be added here) - RoManiak 7-6-2006

Revision as of 01:52, 22 June 2006

Dispositivos Soportados

para la verión v23 SP1 final

  • Allnet
    • All0277
  • Askey
    • RT210W, ver notas de instalación para Siemens SE505 v1
  • Asus
  • Belkin
    • F5D7130/7330 (2mb flash)
    • F5D7230-4 v1444 (2mb flash)
  • Buffalo
    • WHR-G54S
    • WHR-HP-G54
    • WHR-HP-G54S
    • WZR-RS-G54
    • WBR-G54
    • WBR2-G54
    • WBR2-G54s
    • WLA-G54
  • Linksys
    • WRT54G v1.0, v1.1, v2.0, v2.2, v3.0, v3.1, v4.0, v5.0 (2mb flash)
    • WRT54GL v1.0, v1.1
    • WRT54GS v1.0, v1.1, v2.0, v2.1, v3.0, v4.0, v5.0 (2mb flash)
  • Motorola
    • WR850G
  • Ravo
    • W54-RT, ver notas de instalación para Siemens SE505 v1
  • Siemens
    • Gigaset SE505


La mayoría de los enrutadores de arriba, tienen por lo menos 4MB de memoria flash. Todas las versiones del WRT54GS a excepción de la versión v4.0 tienen 8MB de flash. Muchos otros enrutadores, (incluyendo la versión v5.0 del WRT54G y WRT54GS), sólo tienen 2MB de memoria flash. Las versiones "full" y "mini" de DD-WRT requieren 4MB para ser instalados; la versióm "micro" requiere 2MB.

Lista de versiones de WRT54G y sus capacidades


Otras marcas y modelos han sido mencionados como soportados por BrainSlayer y otros en el foro. Sin embargo, no esta claro si hay alguna imágen facilmente obtenible, que funcione en estos modelos, o si has preguntado a BrainSlayer directamente por estos, o si has obtenido el código fuente y los has compilado tu mismo. Sería genial si alguien que haya echo esto, editara esta página del Wiki más adelante.

Precauciones

Sigue todas las instrucciones al pie de la letra. Tendrás problemas si no lo haces.


  • Incorrect flashing procedure can brick your router!
  • You CANNOT flash/backup your firmware over a "https" connection!
  • Firmware flashes and upgrade should be done over a wired Ethernet connection.
    • Flashing via wireless is inherently unstable and can result in a bricked router.
  • Disable your anti-virus-software, as a false-positive virus detection could interrupt the upload.
  • Disable any wireless adapters on your system to ensure that the upload goes through the wired connection!
  • You will not have/need internet access from steps 2 through 5.
  • We recommend you save this webpage and the webpages on how to Recover from a Bad Flash to your hard drive (File - Save Page As, *NOT* a bookmark). This will allow you to review the information offline in the event that something goes wrong.

Instalación vía TFTP

This procedure must not be seen as the standard procedure for flashing: only use it when you are specifically told to do so (for example in the specific instructions for flashing your brand or type of device).

Normally, the GUI flashing method should be used: it should be perfectly adequate for any standard situation. See that section for more information.

(more info to be added here) - RoManiak 7-6-2006