IPTV - blocking multicast on WIFI

From DD-WRT Wiki

(Difference between revisions)
Jump to: navigation, search
Revision as of 15:16, 15 September 2012 (edit)
Sash (Talk | contribs)
(Block Multicast via Firewall - -d mulicast isnt working)
← Previous diff
Revision as of 21:34, 7 October 2012 (edit) (undo)
Sash (Talk | contribs)
(Block Multicast via Firewall)
Next diff →
Line 42: Line 42:
ebtables -A OUTPUT -o "interface to block" --pkttype-type multicast -j DROP --log ebtables -A OUTPUT -o "interface to block" --pkttype-type multicast -j DROP --log
-Finally, enjoy TV, LAN, and Wireless simultaneously+The drawback is ebtables will use sightly mode cpu time.
 +Finally, enjoy TV, LAN, and Wireless simultaneously.
[[Category:Routing]] [[Category:Routing]]
[[Category:Traffic moderation]] [[Category:Traffic moderation]]

Revision as of 21:34, 7 October 2012

Contents


Introduction

This section explains how to use the DD-WRT GUI to configure DD-WRT supporting multicast IPTV traffic while at the same time enable some LAN ports and Wireless Clients working in parallel.

There are 2 ways to achieve this. The first is to unbridge the LAN area that shouldnt get flooded with mulicast packets. The second (and imho more elegand) way is to block mulicast traffic to the interfaces which doesnt need it.

Assumption

In the sample configuration, the TV media receiver is connected to LAN Port 4, and the router Ip is 192.168.1.1. Other configurations work accordingly.

Prerequisites

  1. Ensure that you are at least on DD-WRT 24v1 Firmware, otherwise download the most recent release.
  2. Connect the TV media receiver to Port 4. Connect other LAN connections to Ports 1,2,3

Allow for multicast traffic

  1. Disable (uncheck) "Filter Multicast" on Security-->Firewall

Disable multicast traffic to reach the Wireless adapter

  1. In Wireless-->Basic setting, set "Network Configuration" to "Unbridged", and "Multicast forwarding" to "disabled".
  2. Provide 192.168.3.1 with subnet mask 255.255.255.0 as the IP address for Wireless connections

Setup an additional VLAN

  1. In Setup-->VLANs, check the "tagged" checkboxes for Ports 1,2,3. Then, check the three accoring checkboxes in the VLAN 7 row, uncheck them in the VLAN 0 row, and finally uncheck the "tagged" checkboxes.
  2. Apply the settings and reboot the router

Disable multicast traffic to reach the LAN Ports 1,2,3

  1. In Setup-->Networking, check "Unbridged" for "Network Configuration vlan7", "Multicast forward" to "disable".
  2. Below this entry, provide IP number 192.168.2.1 with subnet mask 255.255.255.0 as the IP address

Enable DHCP for the additional local Networks and final steps

  1. In Setup-->Networking, add two DHCP Servers in the bottom area, one for vlan7, one for eth1 (keep the standard settign for the other fields)
  2. Apply all changes, and reboot the router

Block Multicast via Firewall

Fist you have to load the layer2 firewall modules. Then put in your WIFI interface into the iptables rule ande insert everything into the firewall startup

insmod ebtables
insmod ebtable_filter
ebtables -A FORWARD -o "interface to block" --pkttype-type multicast -j DROP --log
ebtables -A OUTPUT -o "interface to block" --pkttype-type multicast -j DROP --log

The drawback is ebtables will use sightly mode cpu time. Finally, enjoy TV, LAN, and Wireless simultaneously.