How To Flash the WRT54GS v7

From DD-WRT Wiki

(Difference between revisions)
Jump to: navigation, search
Revision as of 21:58, 13 August 2008 (edit)
Soulstace (Talk | contribs)
m (added to Linksys category)
← Previous diff
Revision as of 02:03, 12 December 2008 (edit) (undo)
Avibp (Talk | contribs)

Next diff →
Line 56: Line 56:
3. Use the web inferface to update the firmware to [http://www.dd-wrt.com/dd-wrtv2/downloads/others/tornado/GSv7/vxworkskillerGSv7-v3.bin vxworkskillerGSv7-v3.bin]. 3. Use the web inferface to update the firmware to [http://www.dd-wrt.com/dd-wrtv2/downloads/others/tornado/GSv7/vxworkskillerGSv7-v3.bin vxworkskillerGSv7-v3.bin].
-4. tftp -i 192.168.1.1 PUT [http://www.dd-wrt.com/dd-wrtv2/downloads/v24/Broadcom/Linksys/WRT54GS_v7/dd-wrt.v24_micro_generic.bin dd-wrt.v24-micro_generic.bin] (Windows only)+4. tftp -i 192.168.1.1 PUT [http://www.dd-wrt.com/dd-wrtv2/downloads/v24/Broadcom/Linksys/WRT54GS_v7/dd-wrt.v24_micro_generic.bin dd-wrt.v24_micro_generic.bin] (Windows only)
5. As soon as that is finished do this: ping 192.168.1.1 /t (Windows only) 5. As soon as that is finished do this: ping 192.168.1.1 /t (Windows only)

Revision as of 02:03, 12 December 2008

METHOD FOR EOC, INTEL, AND POSSIBLY OTHER FLASH CHIPS

1. Configure your local LAN ethernet address to 192.168.1.100 and connect your local ethernet to your WRT54GSv7 on one of the four switch ports. Do not use a wlan connection!

2. Disconnect the power cord from the WRT54GSv7.

3. Push the reset button while reconnecting the power cord and hold the button for about 20 seconds.

4. Open your browser and open http://192.168.1.1

5. Use the firmware upgrade dialogue to flash vxworkskillerGSv7-v3.bin.

6. After the dialogue about disconnecting the power cord is shown, disconnect the power cord and reconnect it.

7. Wait for about two minutes.

8. Again disconnect the power cord and reconnect it.

9. Enter "tftp -i 192.168.1.1 put dd-wrt.v24-micro_generic.bin" on your local Windows console and press enter (for linux, tftp 192.168.1.1; mode octet;put dd-wrt.v24-micro_generic.bin or tftp -v -m octet 192.168.1.1 -c put dd-wrt.v24-micro_generic.bin).

10. The file will now be transferred to your router and be flashed. After this is done, your router will boot automatically and you can reach your it at http://192.168.1.1.


ALTERNATE METHOD TO FLASH DD-WRT ON A WRT54GS v7 WITH AN INTEL FLASH CHIP

I just loaded DD-WRT v24 RC7 on two of the WRT54GS v7 with an Intel flash chip. I used the latest vxworkskiller. Below are instructions. Intel chip says JS28F160, C3BD70, and A7397147. Router is dated December 2007. S/N starts with CGNC.

1. Manually configure your IP to 192.168.1.10.

2. Reset router to factory defaults.

3. Update firmware to vxworkskillerGSv7-v3.bin, the update will finish.

4. Watch the lights on the router. Wait until the Power light is solid, then unplug the router.

5. Get "tftp -i 192.168.1.1 PUT dd-wrt.v24-micro_generic.bin" ready in a command prompt and hit enter.

6. Plug the router back in immediately afterwards. If the tftp times out try steps 4, 5, and 6 again.

7. After the tftp is finished wait and watch the router lights.

 6a. The Power light will eventually come one.
 6b. Shortly after that the WLAN light will come on.

8. Try to load the web configuration page about 5 seconds later; you're done!


Another similar method to flash WRT54G v8 and WRT54GS v7.2 (possibly other 7.x)

I've been doing something slightly different on WRT54G v8 and this WRT54GS v7, it hasn't failed me yet, below are the instructions. I have done this on a countless number of WRT54G v8s and just did it on a WRT54GS v7 and it worked just the same. There is no resetting in the middle of this process, just do exactly what it says below, no more and no less. My WRT54GS v7 has a Broadcom BCM5354KFBG CPU and an EON EN29LB160AB-70TCP flash chip and 16MB of Samsung RAM. The FCC ID is Q87-WRT54GSV72 which maybe means it's a v7.2? Serial number starts with CGNE.

1. Use the web interface to reset the router to factory defaults.

2. Manually configure network interface to 192.168.1.10.

3. Use the web inferface to update the firmware to vxworkskillerGSv7-v3.bin.

4. tftp -i 192.168.1.1 PUT dd-wrt.v24_micro_generic.bin (Windows only)

5. As soon as that is finished do this: ping 192.168.1.1 /t (Windows only)

   5a. This will time out repeatedly and then the router will respond between two and six times.
   5b. The router will time out again a few times and then start responding to pings.

6. You're done, try to load 192.168.1.1.